Smartload DEGX1 User Manual Download Page 4

4

Lid Lock

Resistance range

63 Ohms +/- 10 Ohms @ 68°F (20°C)

Safety extra low voltage.

Temperatures

Each cycle, Denim through to Delicate, has a temperature limit, as defined in

the table below, as measured in the exhaust air.  After switching off at the
limit, the temperature has a hysteresis of 5 degrees below these temperatures

when the heat source switches back on.

Denim

Regular

Permanent

Press

Delicate

149°F (65°C) 149°F (65°C) 140°F (60°C) 127°F (53°C)

When tumbling the heat source is turned on as shown in the table below:

Electric

Door Close Direction

4 minutes

Door Open Direction

40 seconds

Element 2/3

Heat

Element 1/3

Heat

Element 2/3

Heat

Element 1/3

Heat

Denim,

ON

ON

OFF

ON

Regular

ON

ON

OFF

ON

P.Press

ON

OFF

OFF

ON

Delicate

ON

OFF

OFF

ON

Air Dry

OFF

OFF

OFF

OFF

Gas

Door Close Direction

4 minutes

Door Open Direction

40 seconds

Gas Ignition

delay

Gas Heating

Denim

30 seconds

3 minutes

30 seconds

No Heat

Regular

30 seconds

2 minutes

30 seconds

P.Press

30 seconds

2 minutes

30 seconds

Delicate

30 seconds

2 minute

10 seconds

Air Dry

No heat

No Heat

Summary of Contents for DEGX1
















Reviews: