background image

                     

 

MGC100 Petrol Genset Controller User Manual                                                                  Page 9 of 16 

4.3.3

 

MANUAL START/STOP 

a)

 

Press 

  to start genset. It will detect complete start and accelerate to  high-speed  running 

automatically. With  high  temperature,  low  oil  pressure, over  speed  and volt abnormal during 
genset running, controller can protect it to stop quickly (Please refer to Start Sequence b-g). 

b)

 

Press 

  to stop the running genset (Please refer to Stop Sequence b-f).   

NOTE:

 

a)

 

The genset can be stopped manually in remote start status; at this time, remote input is inhibited and it will be 
active when remote input is closed again. 

b)

 

After  start  conditions  are  satisfied,  accumulative  running  timer  will  be  initiated;  at  the  same  time,  the  last 
blinking decimal of nixie tube indicates that genset works normally. 

5

 

PROTECTION 

1)

 

Low Oil Pressure: detect after Safety On, Alarm Stop when Low Oil Pressure input is active and 
lasts for 2s. 

2)

 

High Temperature: detect when start, Alarm Stop when High Temperature is active and lasts 
for 2s. 

3)

 

Over Speed: detect when start, Alarm Stop after duration exceeds Over Speed Stop Delay. 

4)

 

Gen  Over  Volt:  Alarm  Stop  when  the  controller  detects  genset  voltage  exceeds  overvoltage 
value and delay exceeds abnormal delay. 

5)

 

Gen Under Volt: Alarm Stop when the controller detects genset voltage less than under voltage 
value and delay less than abnormal delay. 

6)

 

Emergency  Stop:  ETS  output  immediately  when  Emergency  Stop  is active, in  the  meanwhile 
fuel, preheat and start signal are cut off and Emergency Shutdown Alarm Signal is sent. 

7)

 

Fail to Start: Alarm Stop when start failed in preset start times. 

8)

 

Gen Under Frequency: When genset is normal running, controller detects  gen frequency falls 
below under frequency value and  the  “under  frequency”  delay  has  expired, under frequency 
shutdown alarm will be sent. 

9)

 

Gen  Over  Frequency:  Detection  when  start  genset,  if  gen  frequency  exceeds  over  frequency 
value and the “over frequency” delay has expired, over frequency shutdown alarm will be sent. 

Summary of Contents for MGC100

















Reviews: