Smartgen HGM9510 User Manual Download Page 48

Page: 48 / 65

HGM9510 GENSET PARALLEL UNIT

HGM9510 Genset Parallel Unit ISSUE 2013-08-06 Version 1.1 Page 48 of 65

10 SENSORS SETTING

10.1 When reselect sensors, the sensor curve will be transferred into the standard value.

For example, if temperature sensor is SGX (120°C resistor type), its sensor curve is

SGX (120°C resistor type); if select the SGD (120°C resistor type), the temperature

sensor curve is SGD curve.

10.2 When there is difference between standard sensor curves and using sensor, user can

adjust it in “curve type”.

10.3 When input the sensor curve, X value (resistor) must be input from small to large,

otherwise, mistake occurs.

10.4

If select sensor type as “None”, sensor curve is not working.

10.5 If corresponding sensor has alarm switch only, us

er must set this sensor as “None”,

otherwise, maybe there is shutdown or warning.

10.6 The headmost or backmost values in the vertical coordinates can be set as same as

below,

Normal Pressure Unit Conversion Form

kgf/cm

bar

psi

1Pa

1.02x10

－

1x10

－

1.45x10

－

1kgf/cm

9.8x10

0.98

14.2

1bar

1x10

1.02

14.5

1psi

6.89x10

7.03x10

－

6.89x10

－

Summary of Contents for HGM9510


































































Search results

Summary of Contents for HGM9510

Reviews:

Related manuals for HGM9510

Brands by name

Popular brands

Smartgen HGM9510, User Manual

Search results

Summary of Contents for HGM9510

Reviews:

Related manuals for HGM9510

Brands by name

Popular brands