Smartgen HGM9510 User Manual Download Page 2

Page: 2 / 65

Chinese trademark

English trademark

Smartgen

—

make your generator

smart

Smartgen Technology Co., Ltd.

No. 28 Jinsuo Road

Zhengzhou city

Henan Province

P. R. China

Tel:

+86-371-67988888/67981888

+86-371-67991553/67992951

+86-371-67981000(overseas)

Fax:

0086-371-67992952

Web:

http://www.smartgen.com.cn

http://www.smartgen.cn

Email:

[email protected]

photocopying or storing in any medium by electronic means or other) without the written

permission of the copyright holder.

Smartgen Technology reserves the right to change the contents of this document without prior

notice.

Version history

Date

Version

Contents

2013-02-18

1.0

Original release

2013-08-06

1.1

Modify  the  outside  drawing  and  the  main  display  description;
Modify  some  parameters’  default  value;  Add  the  description  of
“Power Management Mode” and “Load Shedding Control”

Summary of Contents for HGM9510


































































Search results

Summary of Contents for HGM9510

Reviews:

Related manuals for HGM9510

Brands by name

Popular brands

Smartgen HGM9510, User Manual

Search results

Summary of Contents for HGM9510

Reviews:

Related manuals for HGM9510

Brands by name

Popular brands