Smartgen HGM6510 User Manual Download Page 30

Page: 30 / 50

HGM6510 GENSET PARALLEL UNIT

HGM6510 Genset Parallel Unit

ISSUE 2013-07-15

Version 1.7

Page 32 of 52

Parameter

Range

Default

Notes

48 Load Ramp Rate

(0-100)%

Load/unload speed %/s

49 Full Power

(0-100)%

80%

Schedule other gen-

sets’

start load percentage

Low

Power

Shutdown

(0-99)%

50%

Schedule other gen-

sets’

stop load percentage

Positive

Freq

Difference

(0-2)Hz

0.2Hz

Frequency

difference

between the generator and
the  bus.  If  it  is  lower  than
the  positive  value  and
higher  than  the  negative
value, then it is considered
as synchronization.

Negative

Freq

Difference

(0-2)Hz

0.1Hz

53 Voltage Difference

(0-30)V

Voltage difference between
generator and bus.

Phase

Angle

Difference

(0-20)°

10°

Initial

phase

difference

between

generator

and

bus.

55 Fail to Sync Delay

(5-300)s

60s

If after synchronization is
initiated, the gen-set fails to
synchronize after the delay
has expired,

“Fail to Sync”

alarm will be initiated.

56 MSC Baud Rate

(0-2)

Baud rate of MSC
0:330K
1:250K
2:125K

Summary of Contents for HGM6510



















































Search results

Summary of Contents for HGM6510

Reviews:

Related manuals for HGM6510

Brands by name

Popular brands

Smartgen HGM6510, User Manual

Search results

Summary of Contents for HGM6510

Reviews:

Related manuals for HGM6510

Brands by name

Popular brands