background image

Longo programmable controller LPC-2.NE1 module

STANDARDS   AND   PROVISIONS:   Standards,   recommendations, 
regulations and provisions of the country in which the devices 

will operate, must be considered while planning and setting up 
electrical   devices.   Work   on   230   VAC   network   is   allowed   for 

authorized personnel only.
DANGER   WARNINGS:   Devices   or   modules   must   be   protected 

from moisture, dirt and damage during transport, storing and 
operation.

WARRANTY CONDITIONS: For all modules LONGO LPC-2 – if no 
modifications are performed upon and are correctly connected 

by   authorized   personnel   –   in   consideration   of   maximum 
allowed  connecting  power,  we  offer  warranty  for   24   months 

from   date   of   sale   to   end   buyer.   In   case   of   claims   within 
warranty time, which are based on material malfunctions the 

producer   offers   free   replacement.   The   method   of   return   of 
malfunctioned   module,   together   with   description,   can   be 

arranged   with   our   authorized   representative.   Warranty   does 
not   include   damage   due   to   transport   or   because   of 

unconsidered corresponding regulations of the country, where 
the module is installed.

This   device   must   be   connected   properly   by   the   provided 
connection scheme in this manual. Misconnections may result 

in device damage, fire or personal injury.
Hazardous voltage in the device can cause electric shock and 

may result in personal injury or death.
NEVER SERVICE THIS PRODUCT YOURSELF!

This device must not be installed in the systems critical for life 
(e.g. medical devices, aircrafts, etc.). 

If   the   device   is   used   in   a   manner   not   specified   by   the 
manufacturer,   the   degree   of   protection   provided   by   the 

equipment may be impaired.

Waste   electrical   and   electronic   equipment   (WEEE)   must   be 
collected separately! 

LONGO LPC-2 complies to the following standards:

EMC: IEC 61131-2

LVD: IEC 61131-2

Vibrations and climatic-mechanical: EN 60068-2-6, EN 60068-

2-27, EN 60068-2-29

Smarteh d.o.o. operates a policy of continuous development. 

Therefore   we   reserve   the   right   to   make   changes   and 
improvements to any of the products described in this manual 

without any prior notice.

MANUFACTURER:
SMARTEH d.o.o.

Trg tigrovcev 1
5220 Tolmin

Slovenia

ii

Summary of Contents for LPC-2.NE1
















Reviews: