Smarteh LBT-1.B01 User Manual Download Page 3

Longo Bluetooth Products LBT-1.B01

STANDARDS   AND   PROVISIONS:   Standards,   recommendations,
regulations and  provisions of  the country in which the devices will
operate, must be considered while planning and setting up electrical
devices. Work on  100 .. 240 V AC  network is allowed for authorized
personnel only.

DANGER   WARNINGS:   Devices   or   modules   must   be   protected   from
moisture, dirt and damage during transport, storing and operation.

WARRANTY CONDITIONS: For all modules LBT-1 – if no modifications
are   performed   upon   and   are   correctly   connected   by   authorized
personnel – in consideration of maximum allowed connecting power,
warranty of 24 months is valid from the date of sale to the end buyer,
but not more than 36 months after delivery from Smarteh. In case of
claims   within   warranty   time,   which   are   based   on   material
malfunctions the  producer offers  free replacement. The  method of
return  of   malfunctioned  module,  together  with  description,  can  be
arranged   with   our   authorized   representative.   Warranty   does   not
include   damage   due   to   transport   or   because   of   unconsidered
corresponding   regulations   of   the   country,   where   the   module   is
installed.
This device must be connected properly by the provided connection
scheme in this manual. Misconnections may result in device damage,
fire or personal injury.
Hazardous  voltage   in  the  device  can  cause  electric  shock  and  may
result in personal injury or death.
NEVER SERVICE THIS PRODUCT YOURSELF!
This device must not be installed in the systems critical for life (e.g.
medical devices, aircrafts, etc.).

If the device is used in a manner not specified by the manufacturer,
the degree of protection provided by the equipment may be impaired.

Waste electrical and electronic equipment (WEEE) must be collected
separately!

LBT-1 devices are developed considering the following standards:

EMC: EN 303 446-1

LVD: EN 60669-2-1

Smarteh   d.o.o.   operates   a   policy   of   continuous   development.
Therefore we reserve the right to make changes and improvements to
any of the products described in this manual without any prior notice.

MANUFACTURER:
SMARTEH d.o.o.
Poljubinj 114
5220 Tolmin
Slovenia

ii

Summary of Contents for LBT-1.B01























Reviews: