WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
WIRELESS CALL SYSTEM
CALL REVIEW
VOLUME
LANGUAGE
REPLACE/ADD
RECORD/ADD
RESET
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
WARNING:
If you do not wait for the Central Monitor to make a melodic tone before pressing the next Nurse Call Button or other
component, each component will be programmed to the same number on the Central Monitor. In this situation, the Central Monitor will
speak one number for the component, but show a different number to represent the room. When multiple components are programmed to
the same number on the Central Monitor,
THE NUMBER SPOKEN WILL NOT CORRESPOND WITH THE NUMBER DISPLAYED
. This may be
useful when multiple devices are being used in the same room, but not for any other situation.
a
d
d
c
c
b
433-NCA Monitor Adaptor (optional) Programming Instructions
Plug Monitor Adaptor into
Nurse Call Port located on the
side of desired the Fall Alarm
Monitor (TL-2100 series)
Plug the sensor pad, floor mat,
or seat belt into phone-style port
at bottom of desired Fall Alarm
Monitor (TL-2100 series)
Press sensor pad, step on floor mat,
or buckle and unbuckle seat belt.
Central Monitor will speak and
display a number. Number shown is
the Monitor Adaptor’s identification
number on the Central Monitor.
Repeat steps “a” and “b” for all Monitor Adaptors that you plan to
add into the Central Monitor system.
Voice
Reset
Safety Auto Reset
Reset
Status
Caregiver
Key
TM
Pad & Monitor
Active when Blinking
Pad & Monitor
Active when Blinking
Low Battery
Pad Lost
Voice
Reset
Safety Auto Reset
Reset
Status
Caregiver
Key
TM
Pad & Monitor
Active when Blinking
Pad & Monitor
Active when Blinking
Low Battery
Pad Lost
Press and hold “Record/
Add” button until you
hear 2 dings and a
melodic tone
Sensor
Pad
f
Wait for the Central Monitor to make
a melodic tone. Then, repeat step “d”
with the next Monitor Adaptor or
follow programming directions for
another component that you would
like to program.
e
a
b
433-MS Motion Sensor (optional) Programming Instructions
Press and hold the
“Record/Add” button until
you hear 2 dings and a
melodic tone.
Turn on the Motion Sensor and
wave a hand in front of the “eye.”
The Central Monitor will speak and
display a number. The Number
shown is the Motion Sensor’s
identification number on the Central
Monitor.
ON OFF
Press “Reset” button to exit
programming mode.
Wait for the Central Monitor to make
a melodic tone. Then, repeat step “b”
with the next motion sensor or follow
programming directions for another
component that you would like to
program.
Press “Reset” button to exit
programming mode.
433-NCA
30A-CMU
30A-CMU
433-CMU
433-CMU
433-CMU
433-MS
5
Sensor Pad
Monitor