background image

13

www.smartavi.com

How to Upgrade the USB Firmware

Open a serial data application such as HyperTerminal. HyperTerminal, Putty, Tera Term are widely 

distributed and free to use.

Connect to the RS-232

at 115200 bits per second,

8 data bits, no parity,

1 stop bit, and no flow control. 

Set Emulation to VT100 and 

setup the ASCII with a line 

delay of 250 milliseconds, 

send line ends with line feeds. 

These settings may be found in 

properties in hyperterminal. The 

ASCII setup is found by clicking 

“ASCII Setup” under the settings 

tab in properties.

In the console type “menuon” and press enter. Next type “bootusb” 

and hold the shift+u button quickly afterwards. If this has been 

done correctly then “USBbtldv1.1” will show up in the console along 

with a prompt. Go to “Send text file” and select the corresponding 

hex file (select “show all” if you don’t see it) and then click open.

Type “pf” at the prompt and the HDMV-Plus will begin loading the firmware for the USB. Reset the 

HDMV-Plus after the console prompt is shown. The console will display ”USB…PASS“ if there were 

no errors when the device is rebooted. 

Summary of Contents for HDMV-Plus

















Reviews: