SMAR DT302, Owner'S Operation And Maintenance Manual

Page: 36 / 84

DT302 – Operation, Maintenance and Instructions Manual
3.2
Concentration/Density Transducer Block Parameter Description
Parameter Description
ST_REV Indicates the level of static data.
TAG_DESC Transducer block description.
STRATEGY This parameter is not checked and processed by transducer block.
ALERT_KEY Number of identification in the plant.
MODE_BLK Indicates the operation mode of transducer block.
BLOCK_ERR Indicates the status associated with hardware or software in the transducer.
UPDATE_EVT Alert for any static data.
BLOCK_ALM Used for configuration, hardware and other fail.
TRANSDUCER_DIRECTORY Used to select several transducer blocks.
TRANSDUCER_TYPE Indicates the type of transducer according to its class.
XD_ERROR Used to indicate calibration status.
COLLECTION_DIRECTORY Specifies the number of transducer index into transducer block.
PRIMARY_VALUE_TYPE Defines the calculation type for transducer block.
PRIMARY_VALUE Value and status used by channel.
PRIMARY_VALUE_RANGE
High and low range limit values, the engineering unit code and the number of digits to the
right of the decimal point to be used for primary value.
CAL_POINT_HI Highest calibrated value.
CAL_POINT_LO Lowest calibrated value.
CAL_MIN_SPAN
Minimum calibration span value allowed. This minimum span information is necessary to
ensure that when calibration is done, the two calibrated points (high and low) are not too
close together.
CAL_UNIT Device description engineering units code index for the calibration values.
SENSOR_TYPE Type of sensor.
SENSOR_RANGE Range of sensor.
SENSOR_SN Serial number of sensor.
SENSOR_CAL_METHOD
Method of last sensor calibration. ISO defines several standard methods of calibration. This
parameter is intended to record that method, or if some other method was used.
SENSOR_CAL_LOC
Location of last sensor calibration. This describes the physical location at which the
calibration was performed.
SENSOR_CAL_DATE Date of the last sensor calibration.
SENSOR_CAL_WHO Name of person who is in charge of last calibration.
SENSOR_ISOLATION_MTL Defines the construction material of the isolating diaphragms.
SENSOR_FLUID Defines the type of fill fluid used in the sensor
SECONDARY_VALUE Secondary value (temperature value), related to the sensor.
SECONDARY_VALUE_UNIT Engineering units to be used with SECONDARY_VALUE.
PRESS_LIN_NORMAL Linear normalized pressure value.
PRESS_NORMAL Normalized pressure value.
PRESS_CUTOFF Cutoff pressure value.
CUTOFF_FLAG Bypass flag for Pressure value.
DIGITAL_TEMPERATURE Digital temperature value.
DIFF Differential pressure value.
YDIFF Differential pressure value.
CAPACITANCE_LOW Low capacitance value.
CAPACITANCE_HIGH High capacitance value.
BACKUP_RESTORE This parameter is used to do backup or to restore configuration data.
SENSOR_RANGE_CODE Indicates the sensor range code.
COEFF_POL0 Polynomial coefficient 0.
COEFF_POL1 Polynomial coefficient 1.
COEFF_POL2 Polynomial coefficient 2.
COEFF_POL3 Polynomial coefficient 3.
COEFF_POL4 Polynomial coefficient 4.
COEFF_POL5 Polynomial coefficient 5.
COEFF_POL6 Polynomial coefficient 6.
COEFF_POL7 Polynomial coefficient 7.
COEFF_POL8 Polynomial coefficient 8.
COEFF_POL9 Polynomial coefficient 9.
COEFF_POL10 Polynomial coefficient 10.
COEFF_POL11 Polynomial coefficient 11.
POLYNOMIAL_VERSION Indicates the polynomial version.
CHARACTERIZATION_TYPE Indicates the type of characterization curve.
CURVE _BYPASS_LD Enable and disable the characterization curve.
CURVE_LENGTH Indicates the length of characterization curve.
CURVE_X Input points of characterization curve.
CURVE_Y Output points of characterization curve.
CAL_POINT_HI_BACKUP Indicates the backup for high calibration point.