Smacq Technologies USB-3200 Series User Manual Download Page 12 | Manualshive

Page: 12 / 40

Smacq Technologies USB-3200 Series User Manual Download Page 12

11 |

Calibration

Recommended
warm-up time

No less than 20Minutes

Recommended
calibration interval

1 year

Bus interface

USB

USB2.0 High Speed interface

Power supply requirements

USB interface power
supply

4.5 V ~ 5.5 V

Typical current without
load

400mA

Maximum Load

600mA

Physical properties

Size (mm)

Without connectors: 150*96*28
Connectors included: 150*112*28

Weight (g)

Without connectors: about 185g
Connectors included: about 230g

I/O connectors

Bolt terminals

Bolt terminal
connection

16 AWG ~ 28 AWG

USB connectors

USB Type B

1.4.

Product unpacking

Precautions

To prevent electrostatic discharge (ESD) from damaging the device, please note the following:



Please wear a grounding wristband or touch a grounded object first to ensure being

grounded.



Before removing the equipment from the packaging, please first connect the anti-static

packaging to the grounded object.



Do not touch the exposed pins of the connector.

«
...
10
11
12
13
14
...
»

Summary of Contents for USB-3200 Series









































Reviews:

No comments