SMA Sunny Boy SB 1100LV Page 24 Installation Manual Download | Manualshive

Page: 24 / 62

background image

Installation

SMA

Technologie AG

Page 24

SB1100LV-11:SE2006

Installation Guide

Connecting the AC plug with PG16

To connect a cable with a cross-section between 13.5 mm² and 16 mm², proceed as
follows.
1.

First of all, slide the pressure screw with the PG16 screw fitting onto the cable.
Now slide the threaded sleeve over the cable.

2.

Now connect the individual conductors to the socket element
in sequence.
- Protective earth PE (green/yellow) to the screw terminal

with the earth sign. Make sure that the PE earth wire is
longer than the N and L connected wires.

- Neutral conductor N (blue) to screw terminal 1.
- Live L (brown or black) to screw terminal 2.
- Terminal 3 remains unused.

3.

Make sure the wires are securely connected.

4.

Now screw the threaded sleeve onto the socket element and tighten it.

Threaded sleeve

Pressure screw with

PG16 screw fitting

Terminals in the

socket element

Threaded sleeve

Pressure screw with

PG16 screw fitting

Socket element

Connected wires

Threaded sleeve screwed

onto socket element

Pressure screw with

PG16 screw fitting

«
...
22
23
24
25
26
...
»

Summary of Contents for Sunny Boy SB 1100LV































































Reviews:

No comments

Related manuals for Sunny Boy SB 1100LV

Brand: Icy Box Pages: 2

Brand: Wacker Neuson Pages: 22

Brand: TTI Pages: 7

Brand: Harman Kardon Pages: 16

Brand: National Communications Pages: 20

Brand: Parallax Pages: 3

Brand: Satel Pages: 2

Brand: AGM Pages: 71

Digi Edgeport/1i

Brand: Inside Out Networks Pages: 22

Brand: Eaton Pages: 86

Brand: tams elektronik Pages: 68

Brand: Panasat Pages: 33

Cobalt Alpha Series

Brand: DCCconcepts Pages: 25

Avtron SAFETach III SV850

Brand: Nidec Pages: 8

Brand: Larson Electronics Pages: 3

Brand: aci Pages: 8

Brand: KTI Networks Pages: 43

Brand: LG Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands