7
OPERATION
As the user’s hands enter the beam’s effective range, the beam is reflected
back into the sensor receiver and activates the solenoid valve allowing
water to flow from the faucet. Water will flow until the hands are removed or
until the faucet reaches its automatic time out setting.
A
C
D
10 Sec.
10 Sec.
10 Sec.
When assistance is required, please contact Sloan Technical Support at:
Close supply
stop(s).
B
A30
A10 / A20
A30
A10 / A20
Loosen screw
with hex wrench
and remove cap.
• Adjust temperature to desired
limit
• Adjust screw to meet limit
setting
Replace cover
and tighten
screw with hex
wrench.
E
Supply Stop
Gasket
Strainer/
Filter
Flex Hose
3/8” Compression Connector
Open
supply stop(s).
Wait ten (10)
seconds before
using faucet.
10 Sec.
F
HOT LIMIT STOP ADJUSTMENT
DO NOT USE
abrasive or chemical cleaners (including chlorine bleach) to clean faucets that may
dull the luster and attack chrome or special decorative finishes. Use
ONLY
mild soap and water,
then wipe dry with clean cloth or towel.
While cleaning the bathroom tile, protect the faucet from any splattering of cleaner. Acids and
cleaning fluids will discolor or remove chrome plating.
1. Problem Faucet does not function.
Cause Adhesive packaging label affixed over sensor eye.
Solution Remove adhesive label from sensor eye.
Cause Permanent Off Activated shown by RED flashing
LED.
Solution Touch button on sensor window for 2 seconds,
RED flashing LED will stop and confirmed with
ORANGE LED.
2. Problem Faucet delivers water in an uncontrolled manner.
Solution Contact Sloan Technical Support (see below).
3. Problem Faucet does not deliver any water with hands in sensor
range.
Indicator Solenoid valve produces an audible “click.”
Cause Water supply stop(s) closed.
Solution Open water supply stop(s).
Cause Water supply stop strainer(s) clogged.
Solution
Turn off water at supply stop(s). Remove, clean
and reinstall water supply stop strainer(s). Replace
strainer(s), if required. Turn on water at supply
stop(s).
Indicator Solenoid valve does not produces an audible “click.”
Cause Battery low.
Solution Replace battery (refer to battery replacement).
Solution Contact Sloan Technical Support (see below)
4. Problem
After removing label water does not flow.
Use this installation guide as a target by placing it
in front of the sensor (approx. 1-1/2” away) until water
begins flowing, then remove installation instruction
from sensor. Water will stop flowing, wait 10 seconds
before using faucet.
5. Problem Faucet delivers only a slow flow or dribble when sensor is
activated.
Cause Water supply stop(s) are partially closeSolution
Completely open water supply stop(s).
Cause Water supply stop strainer(s) clogged.
Solution
Turn off water at supply stop(s). Remove, clean
and reinstall water supply stop strainer(s). Replace
strainer(s), if required. Turn on water at supply
stop(s).
Cause Spray head is clogged.
Solution
Remove, clean, and reinstall spray head. Replace
spray head, if required.
Solution Contact Sloan Technical Support (see below).
6. Problem Faucet does not stop delivering water or continues to drip
after user is no longer detected.
Solution Contact Sloan Technical Support (see below).
7. Problem LED indicator blinks RED when faucet is in use.
Cause Battery low.
Solution Replace battery (refer to battery replacement)
8. Problem The water temperature is too hot or too cold on a faucet
connected to hot and cold supply lines.
Cause Supply stops are not adjusted properly.
Solution Adjust supply stops.
Cause For models with integral mixing valve – Mixing valve
is set improperly for the water temperature desired.
Solution
Rotate mixing valve handle clockwise to decrease
water temperature or counterclockwise to increase
water temperature.
