background image

Install sensor (EL-1500 or EL-1500-L) into the 2-gang electrical 

box using two (2) long screws provided. Ensure that sensor lens 

faces outward and horizontally from finished wall.

Mount assembled yoke to electrical box.

Install sensor cover plate and secure with tamper-proof screws 

(EL-152).

Connect solenoid lead to terminal labeled “TO VALVE” of sensor.

C

Connect remaining solenoid lead to remaining 24 volt source lead.

D

A

Be certain power is OFF to prevent damage to electrical components. 

Connect sensor to transformer and solenoid coil EXACTLY as shown.

B

Connect 24 volt source lead to terminal labeled “24 VAC IN” of sensor.

Wiring Diagram

Wiring Diagram for One Flush Valve

SOLENOID

VALVE

SENSOR

A

SENSOR 

(EL-1500 or EL-1500-L)

GRD

UNIT #1

UNIT #2 

THRU #10 

(IF USED)

120 VAC

24 VAC

EL-1500-L SENSOR

COIL WIRE

24 VAC COIL

EL-1500-L SENSOR

COIL WIRE

24 VAC COIL

Wiring Diagram for Multiple Flush Valves

7 - ELECTRICAL HOOK-UP

8 - INSTALL SENSOR, YOKE AND COVER PLATE

Note: Valve is not shown to complete assembly with control stop on.

E

Connect transformer and sensor wire leads to coil wire leads.

F

Secure solenoid operator to Flushometer by tightening the solenoid 

coupling. Tighten housing retention nut.

9 - FLUSH OUT SUPPLY LINE

D

Open control stop. Turn on water supply 

to flush line of any debris or sediment.

C

Remove flushometer cover and lift 

out Inside parts assembly. Install 

flushometer cover wrench tight.

B

Remove flushometer cover.

E

Shut off control stop, remove cover and reinstall Inside Parts 

Assembly. Install flushometer cover wrench tight. Do Not open 

control stop until Step 13.

A

Make sure control stop is CLOSED.

B

5

B

C

YOKE 

(EL-168-A)

Summary of Contents for 152 ES-S TMO SWB









Reviews: