manualshive.com logo in svg

Sleipner SE-IP120, Installation Manual, Page: 2 / 28

Share
Download
Sleipner SE-IP120 Installation Manual Download Page 2

2

2685

13

2021

-

SE IP 80 & SE IP 120

Sleipner Motor AS

P.O. Box 519, Arne Svendsensgt. 6-8

N-1612 Fredrikstad, Norway 

MC_0020

Contents

Products 

SE120/215T-24IP - SE120 Tunnel thruster, 24V-IP 

SE80/185T-24IP - SE80 Tunnel thruster, 24V-IP 

SE80/185T-12IP - SE80 Tunnel thruster, 12V-IP 

Installation Manual 

Responsibility of the installer ...................................................................................................................................................................3

 

Thruster Measurements   ....................................................................................................................................................................... 4 

Thruster Specifications

 ........................................................................................................................................................................... 5 

Technical Specifications  

 ....................................................................................................................................................................... 5 

Positioning of the tunnel / thruster .......................................................................................................................................................... 6 

Tunnel Length ......................................................................................................................................................................................... 7 

Tunnel installation in sail boats ............................................................................................................................................................... 8 

Water Deflection

 ..................................................................................................................................................................................... 9 

Tunnel ends .......................................................................................................................................................................................... 10 

Tunnel installation ..........................................................................................................................................................................  11 - 12 

Stern tunnel installation ........................................................................................................................................................................ 13 

Gear Leg & Motor Bracket Installation.................................................................................................................................................. 14 

Propeller Installation ............................................................................................................................................................................. 15 

Motor Installation .................................................................................................................................................................................. 16 

Thruster Electrical Installation .............................................................................................................................................................. 17 

Electrical Specifications 

 ....................................................................................................................................................................... 18 

Technical Wiring Diagram  ............................................................................................................................................................. 19 - 20 

Control Panel Cable Installation  .......................................................................................................................................................... 21 

Control Panel Installation ..................................................................................................................................................................... 22 

 

Pre-delivery Checklist  .......................................................................................................................................................................... 23

 

Service and Support........................................................................................................................................................................... 24

Product Spare Parts and Additional Resources .............................................................................................................................. 24

Warranty Statement ............................................................................................................................................................................ 24

Summary of Contents for SE-IP120





























Reviews:

No comments