SYSTEM CHECK
MILLIVOLT VALVES
Light the gas appliance following the lighting instructions that came with the appliance. Confirm that the pilot flame is
ON
;
and the control knob on the gas valve is in the
ON
position for the main gas valve to operate.
Model: 3003P
REV. 12-7-12 Page 6
LEARNING TRANSMITTER TO RECEIVER
Each transmitter uses a unique security code. It will be necessary to press the
LEARN
button on the receiver to accept
the transmitter security code upon initial use, if batteries are replaced, or if a replacement transmitter is purchased from
your dealer or the factory. In order for the receiver to accept the transmitter security code, be sure the slide button on
the receiver is in the
REMOTE
position; the receiver will not LEARN if the slide switch is in the
ON
or
OFF
position. The
LEARN
button in located on the front face of the receiver; inside the small hole labeled LEARN. Using a small screw-
driver or end of a paperclip gently press and release the black LEARN button inside the hole. When you release the
LEARN button the receiver will emit an audible “beep”. After the receiver emits the
beep press the transmitter
MODE
button and release. The receiver will emit several
beeps indicating that the transmitter’s code has been accepted into the receiver.
The microprocessor that controls the security code matching procedure is controlled
by a timing function. If you are unsuccessful in matching the security code on the first
attempt, wait 1-2 minutes before trying again – this delay allows the microprocessor to
reset its timer circuitry – and try up to two or three more times.
Fig. 18 Learn Button
•
Slide the 3-position button on the remote receiver to the
ON
position. The main gas flame (fire) should light.
• Slide the button to
OFF
. The flame should extinguish (the pilot flame will remain on).
• Slide the button to REMOTE (the center position), and then press the MODE button on the transmitter to change
the system to
ON
. The main gas flame should ignite.
• Press the MODE button on the transmitter to change the system to
OFF.
The flame should extinguish (the pilot
flame will remain on).
• Press the MODE button on the transmitter to change the system to
THERMO
. Advance the SET temperature on the
transmitter to a temperature of a least 2°F (1°C) above the ROOM temperature displayed on the LCD screen. With this
manual setting, the normal thermostatic cycle is overridden and the system flame will ignite. Place the SET temperature
to at least 2°F (1°C) below the room temperature and the system flame will extinguish in a few seconds. Thereafter, it
should continue to cycle on and off thermostatically approximately every two minutes as the ROOM temperature changes,
but only when the temperature differential between ROOM and SET temperatures differ at least 2°F (1°C). (The 2°F dif-
ferential is the factory setting.)
ELECTRONIC IGNITION SYSTEMS
• Slide the 3-position button on the remote receiver to the
ON
position. The spark electrode should begin sparking to
ignite the pilot (the pilot may ignite after only one spark). After the pilot flame is lit, the main gas valve should open and
the main gas flame should ignite.
• Slide the button to
OFF
. The main gas flame and pilot flame should BOTH extinguish.
• Slide the button to
REMOTE
(the center position), and then press the
MODE
button on the transmitter to change the
system to
ON
. The spark electrode should begin sparking to ignite the pilot. After the pilot is lit, the main gas valve
should open and the main gas flame should ignite.
• Press the MODE button on the transmitter to
OFF
. The main gas flame and pilot flame should BOTH extinguish.
• Press the MODE button on the transmitter to change the system to
THERMO
. Advance the SET temperature on the
transmitter to a temperature at least 2°F (1°C) above the ROOM temperature displayed on the LCD screen. With this
manual setting the normal thermostatic cycle is overridden and the system flame will ignite. Place the
SET
temperature at
least 2°F (1°C) below the room temperature and the system flame will extinguish in a few seconds. Thereafter, it should
continue to cycle ON and OFF thermostatically approximately every two minutes as the ROOM temperature changes, but
only when the temperature differential between ROOM and SET temperatures differ at least 2°F (1°C). (The 2°F differen-
tial is the factory setting.)
