Skyrc Ultimate 10amp x2 Instruction Manual Download Page 2

Page: 2 / 32

Ultimate 200W×2

TABLE OF CONTENTS

Introduction......................................................................................................................................02

Special features..............................................................................................................................04

Warning and safety notes..............................................................................................................07

Program flow chart........................................................................................................................10

Lithium polymer balance charge program connection diagram..................................................11

Initial parameter setup (users set up)...........................................................................................13

....................................................................................15

Charging lithium battery in the charge mode...............................................................................16

Charging lithium battery in the balance mode.............................................................................17

Charging lithium battery in the fast charge mode........................................................................18

Charging lithium battery in the s

mode

.................

.......19

Discharging of lithium battery........................................................................................................19

Charging NiCd/NiMH battery in the charge mode

.....................

Discharge of NiCd/NiMH battery..................................................................................................21

..................................

Charging Pb (lead-acid) battery in the charge mode..................................................................22

Discharging of the Pb battery.......................................................................................................22

Storage data program..................................................................................................................23

Load data program.......................................................................................................................24

Various information in the program.............................................................................................24

Warning and error message........................................................................................................25

Recommended accessories........................................................................................................26

Conformity declaration.................................................................................................................27

Specification..................................................................................................................................29

Commonly used terms.................................................................................................................30

Warranty and service....................................................................................................................30

Lithium battery (LiIon/LiPo/LiFe) program

torage

.................................................

....

.................................................

Charge/discharge and discharge/charge cycle of NiCd/NiMH battery....

Maximum circuit power chart.......................................................................................................28

Summary of Contents for Ultimate 10amp x2

































Search results

Summary of Contents for Ultimate 10amp x2

Reviews:

Related manuals for Ultimate 10amp x2

Brands by name

Popular brands

Skyrc Ultimate 10amp x2, Instruction Manual

Search results

Summary of Contents for Ultimate 10amp x2

Reviews:

Related manuals for Ultimate 10amp x2

Brands by name

Popular brands