Skyjack SJKB-40-D Operating Maintenance Instructions & Part List Download Page 81

Page: 81 / 213

SECTION 4, Page 30

SJKB-40-D, SJKB-40-D/F

JUN. 1999

TROUBLESHOOTING (Cont.)

TROUBLE

PROBABLE CAUSE

REMEDY

HYDRAULIC SYSTEM (Cont.)

NO PLATFORM ROTATE
RIGHT

Stuck or defective platform rotate
right valve 4H-37A.

Defective platform rotary actuator
RA1

Stuck counter balance valve CB5.

Clean Valve. Replace if
defective.

Check Actuator. Replace if
defective.

Clean Valve. Replace if
defective.

NO PLATFORM ROTATE
RIGHT OR LEFT

Plugged orifice 04.

Defective platform rotary actuator
RA1.

Clean Orifice.

Check Actuator. Replace if
defective.

NO TELESCOPE RE-
TRACT

Stuck or defective telescope retract
valve 4H-38A.

Stuck counter balance valve CB4.

Clean Valve. Replace if
defective.

NO TELESCOPE EX-
TEND

Stuck or defective telescope
extend valve 4H-39A.

Stuck counter balance valve CB3.

Clean Valve. Replace if
defective.

TELESCOPE CYLINDER
DRIFTS IN

Leaking or defective counter
balance valve CB4.

Telescope cylinder C3 by passing
internally.

Check Valve. Replace if
defective.

Rebuild Cylinder. Replace if
damaged.

NO RISER BOOM DOWN

Stuck or defective riser boom
down valve 4H-13A.

Stuck counter balance valve CB2.

Clean Valve. Replace if
defective.

NO RISER BOOM UP

Stuck or defective riser boom up
valve 4H-14A.

Clean Valve. Replace if
defective.

RISER BOOM DRIFTS
DOWN

Leaking or defective counter
balance valve CB2.

Riser cylinder C1 by passing
internally.

Check Valve. Replace if
defective.

Rebuild Cylinder. Replace if
damaged.

NO PLATFORM LEVEL-
ING DOWN

Stuck or defective platform level
down valve 4H-40A.

Stuck counter balance valve CB1.

Leveling master cylinder by
passing internally.

Stuck counter balance valve
CB12.

Clean Valve. Replace if
defective.

Rebuild cylinder. Replace if
damaged.

Clean Valve. Replace if
defective.

Summary of Contents for SJKB-40-D






















































































































































































































Search results

Summary of Contents for SJKB-40-D

Reviews:

Related manuals for SJKB-40-D

Brands by name

Popular brands

Skyjack SJKB-40-D, Operating Maintenance Instructions & Part List

Search results

Summary of Contents for SJKB-40-D

Reviews:

Related manuals for SJKB-40-D

Brands by name

Popular brands