manualshive.com logo in svg

Skyjack SJKB-40-D, Operating Maintenance Instructions & Part List

The Skyjack SJKB-40-D user manual is your essential guide to operating this state-of-the-art aerial work platform. Download the comprehensive manual for free from manualshive.com, ensuring you have access to all the necessary instructions and safety precautions required for a seamless and efficient experience with this exceptional product.

Share
Download
background image

SECTION 4, Page 8

SJKB-40-D, SJKB-40-D/F

JUN. 1999

TROUBLESHOOTING (Cont.)

TROUBLE

PROBABLE CAUSE

REMEDY

ELECTRICAL SYSTEM (Cont.)

NO  RISER  BOOM  UP
FROM PLATFORM

1.

Loose  or  broken  wire  #99  from
platform terminal block TB1 to riser
up/down switch S15.

2.

Defective  riser  up/down  switch
S15.

3.

Loose or broken wire #14 from riser
up/down  switch  S15  to  platform
terminal block TB2.

4.

Loose  or  broken  wire  #14  from
platform  terminal  block  to  base
terminal block TB3.

1.

Check  Continuity.    Replace  if
defective.

2.

Check  Switch.    Replace  if
defective.

3.

Check  Continuity.    Replace  if
defective.

4.

Check  Continuity.    Replace  if
defective.

NO RISER BOOM DOWN
FROM PLATFORM

1.

Loose  or  broken  wire  #08  from
platform terminal block TB1 to riser
up/down switch S15.

2.

Defective  riser  up/down  switch
S15.

3.

Loose or broken wire #13 from riser
up/down  switch  S15  to  platform
terminal block TB2.

4.

Loose  or  broken  wire  #13  from
platform terminal; block TB2 to base
terminal block TB3.

1.

Check  Continuity.    Replace  if
defective.

2.

Check  Switch.    Replace  if
defective.

3.

Check  Continuity.    Replace  if
defective.

4.

Check  Continuity.    Replace  if
defective.

NO MAIN BOOM DOWN
FROM  PLATFORM  OR
BASE CONTROLS

1.

Loose or broken wire #30 from base
terminal block TB3 to relay 30CR.

2.

Loose or broken wire #02 from relay
30CR to base terminal block TB3.

3.

Defective relay 30CR.

4.

Loose or broken wire #09 from base
terminal block TB3 to relay 30CR.

5.

Loose or broken wire #30A from
relay  30CR  to  main  boom  down
valve coil 4H-30A.

6.

Defective main boom down coil 4H-
30A.

7.

Loose or broken wire #02 from main
boom down valve coil 4H-30A to
base terminal block TB3.

8.

Open diode D30-1.

1.

Check  Continuity.    Replace  if
defective.

2.

Check  Continuity.    Replace  if
defective.

3.

Check Relay.  Replace if defective.

4.

Check  Continuity.    Replace  if
defective.

5.

Check  Continuity.    Replace  if
defective.

6.

Check  Continuity  through  coil.
Replace if defective.

7.

Check  Continuity.    Replace  if
defective.

8.

Check Diode.  Replace if defective.

NO  MAIN  BOOM  UP
FROM  PLATFORM  OR
BASE CONTROLS

1.

Loose or broken wire #31 from base
terminal block TB3 to relay 31CR.

2.

Loose or broken wire #02 from relay
31CR to base terminal block TB3.

3.

Defective relay 31CR.

4.

Loose or broken wire #09 from base
terminal block TB3 to relay 31CR.

5.

Loose or broken wire #31A from
relay 31CR to main boom up valve
coil 4H-31A.

1.

Check  Continuity.    Replace  if
defective.

2.

Check  Continuity.    Replace  if
defective.

3.

Check Relay.  Replace if defective.

4.

Check  Continuity.    Replace  if
defective.

5.

Check  Continuity.    Replace  if
defective.

Summary of Contents for SJKB-40-D






















































































































































































































Reviews:

No comments

Related manuals for SJKB-40-D

Pacific Orchard-Rite MONOBOOM 9600 Series Owner'S Manual preview
Orchard-Rite MONOBOOM 9600 Series
Brand: Pacific Pages: 40
Wesco LDT-3080 Operating Instructions And Parts Manual preview
LDT-3080
Brand: Wesco Pages: 5
Wesco 260201 Instruction Manual preview
260201
Brand: Wesco Pages: 7
TEUPEN LEO 15 GT Translation Of The Original Operating Instructions preview
LEO 15 GT
Brand: TEUPEN Pages: 208
Niuli Maxiton GTJZ Series Operation And Maintenance Manual preview
Maxiton GTJZ Series
Brand: Niuli Pages: 42

Brands by name

Popular brands

Load more brands