Skyjack SJKB-40-D Operating Maintenance Instructions & Part List Download Page 164

Page: 164 / 213

SECTION 6, Page 51

SJKB-40-D, SJKB-40-D/F

JUN. 1999

Parts List Continued from Page 49.

707387

• GUARD, Lower control panel

103962

• • BOLT, Machine head #10-32 x 1/2” lg.

104185

• • WASHER, Lock #10

104003

• • NUT, Hex #10-32

701927

• GUARD, Toggle switch hinged

701445

• PLUG, Knockout 3/8”

(Ref.)

• LABEL, Base control panel

706923

• LABEL, Dual fuel base control panel

707233

• LABEL, Diesel base control panel

701523

• CABLE TIE MOUNT, Self-adhesive

102921

• DIODE, 6 Amp/1000PIV

706074

• SNAP-ON FERRITE CORE

703077

• STRAIN RELIEF, 3/4”

103041

• STRAIN RELIEF, 5/8”

103036

• STRAIN RELIEF, Strait plastic

707722

• WIRE HARNESS, Main manifold

707709

• WIRE HARNESS, Governor (All Kubota Engines)

708958

• WIRE HARNESS, Governor (All Ford Engines)

707708

• WIRE HARNESS, Engine control

703720

• LIGHT, Indicator amber (diesel only)

708560

• SUB-ASSEMBLY DIODE

708559

• SUB-ASSEMBLY DIODE

702262

• PLUG, 1/2” Knockout (All Ford Engines)

FIGURE 6-25. BASE CONTROL/ELECTRICAL PANEL ASSEMBLY

Index

No.

Skyjack

Part No.

Description

1 2 3 4 5 6 7

Units

per

Assy.

Summary of Contents for SJKB-40-D






















































































































































































































Search results

Summary of Contents for SJKB-40-D

Reviews:

Related manuals for SJKB-40-D

Brands by name

Popular brands

Skyjack SJKB-40-D, Operating Maintenance Instructions & Part List

Search results

Summary of Contents for SJKB-40-D

Reviews:

Related manuals for SJKB-40-D

Brands by name

Popular brands