Skope VF-ICE Series User Manual Download Page 12

12

Servicing

User Manual

SKOPE VF-ICE Series Ice Storage Cabinet

3

  Servicing 

Cleaning

Ensure the ice storage cabinet is disconnected from the power supply 
before cleaning.  

Cabinet

Periodically wipe the inside and outside of the cabinet with a damp cloth, 
taking care to keep moisture away from electrical parts.  

Condenser

Coil

To ensure trouble-free performance, we strongly urge monthly cleaning with 
a soft brush to remove dust and fluff. A more thorough cleaning is 
recommended every six months, by qualified service personnel. The 
condenser coil 

must

 be kept clean for efficient and reliable operation.

To clean the condenser coil

WARNING

Twin unit ice storage cabinets have two separate power 

supplies. Ensure both supplies are disconnected before 

undertaking any service or maintenance work. 

WARNING

Disconnect the ice storage cabinet from the power supply 

before cleaning the condenser coil.

1. Disconnect the ice storage cabinet from the power supply.

2. Remove the sign assembly. Lift the assembly up and off the sign sides and if 

necessary unplug it from the cabinet.

3. Clean the condenser coil 

with a soft brush.

4. Refit the sign assembly and reconnect the ice storage cabinet to the power 

supply.

Summary of Contents for VF-ICE Series

















Reviews: