manualshive.com logo in svg

Skope PG1300VF, User Manual

Share
Download
Skope PG1300VF User Manual Download Page 16

16

Servicing

User Manual

SKOPE Pegasus Vertical Freezer - Integral

Troubleshooting

Complaint

Possible Cause

Repair

1. Cabinet not 

operating and 
no controller 
display:

• Loss of power supply.

• Check mains power supply.

2. Cabinet lights 

not operating:

• Failed LED light tube.

• Replace LED light tube (see 

page 14).

• Controller high temperature 

shutdown alarm ‘CHt’.

• Determine cause and 

eliminate (see ppage 10).

• Cabinet ENSTO supply plug 

not plugged into control box.

• Reconnect plug.

3. Power 

consumption 
is higher than 
expected:

• Unit operating too hot.

• Clean condenser. Ensure 

the chiller is installed with 

good ventilation above the 

refrigeration unit.

• Cabinet doors are opened 

excessively.

• Keep door/s open for 

minimum time.

4. Product is too 

warm and 
spoiling:

• Restricted cabinet airflow.

• Ensure product is not 

blocking airflow slots and the 
product is no closer than 
50mm from the cabinet top.

• Temperature setpoint is too 

warm.

• Adjust setpoint (see 

page 10).

5. Warm cabinet 

temperatures 
and/or 
compressor 
operating for 
long periods 
(more than 1 
hour):

• Blocked condenser.

• Clean condenser (see 

page 15).

• Poor refrigeration unit 

ventilation.

• Ensure the cabinet is 

installed with good 
ventilation around the front 
of the refrigeration unit (see 
page 6). 

Summary of Contents for PG1300VF


















Reviews:

No comments

Brands by name

Popular brands

Load more brands