manualshive.com logo in svg

Skope PG1300VF, User Manual

Share
Download
Skope PG1300VF User Manual Download Page 14

14

Servicing

User Manual

SKOPE Pegasus Vertical Freezer - Integral

3

  Servicing

Lighting

Cabinet

Interior Lights

The cabinet interior is lit by an LED tube fitted behind the diffuser at the top 
of the cabinet (PG600VF) or behing the centre pillar (PG1300VF). See the 
table below for LED tube specifications.

LED tube specifications

To replace the interior LED light tube

Cabinet

LED tube description

SKOPE part No.

PG600VF

Ecopoint 5W 360mm T8 LED tube

ELL10435

PG1300VF

Ecopoint 22W 1200mm T8 LED tube

ELL10436

1. Disconnect the chiller from the mains power supply.

2. Remove the diffuser by 

squeezing it until it is 
released from the 
housing, and then push 
the diffuser out of the way 
(single door cabinet 
pictured for clarity).

3. Rotate the LED tube until 

the pins on the ends of the 
tube align with the slots, 
then slide it out.

4. Fit a new LED tube and 

clip the diffuser back into 
place. Reconnect to the 
power supply.

Summary of Contents for PG1300VF


















Reviews:

No comments

Brands by name

Popular brands

Load more brands