manualshive.com logo in svg

Skope B550-2, User Manual

Share
Download
Skope B550-2 User Manual Download Page 15

15

SKOPE B550/660-2 and BME550-2

Servicing

User Manual

Troubleshooting

Figure 12: Sign 

Corner Detail

Sign Top Cover

Corner Notch

Sign Panel 
End Strip

Sign Panel

Figure 11: Removing 

Sign Panel

Sign Top Cover

Corner 
Notch

Complaint

Possible Cause

Repair

1. Cabinet not 

operating and no 
controller display:

• Loss of power 

supply.

• Check mains power supply and 

check the cabinet isolating switch is 
turned on (see “Isolating Electrics” 
on page 12).

2. Cabinet interior 

light not 
operating:

• Failed 

fluorescent tube.

• Replace fluorescent tube (see 

“Lighting” on page 14).

• Controller alarm.

• Determine cause and eliminate 

(“Controller Alarms” on page 10).

• Not switched on

• Switch on at controller (some 

models only, see “Controller Display” 
on page 9)

3. Power 

consumption is 
higher than 
expected:

• Unit operating too 

hot.

• Clean the condenser coil (see 

“Cleaning” on page 13). Ensure the 
chiller is installed with good 
ventilation around the refrigeration 
unit and within its maximum 
operating temperature (see 
“Positioning the Cabinet” on page 5).

• Cabinet door is 

opened 
excessively.

• Keep door open for minimum time.

4. Product is too 

warm and 
spoiling:

• Restricted 

cabinet airflow.

• Ensure product is not blocking 

airflow slots and there is air space 
around all the product.

• Temperature 

setpoint to too 
warm.

• Adjust setpoint (“Temperature 

Setpoint” on page 11).

5. Warm cabinet 

temperatures 
and/or 
compressor 
operating for long 
periods (more 
than 1 hour):

• Blocked 

condenser.

• Clean the condenser coil (see 

“Cleaning” on page 13).

• Poor refrigeration 

unit ventilation.

• Ensure the cabinet is installed with 

good ventilation around the 
refrigeration unit and within its 
maximum operating temperature 
(see “Positioning the Cabinet” on 
page 5).

Summary of Contents for B550-2
















Reviews:

No comments

Brands by name

Popular brands

Load more brands