manualshive.com logo in svg

Skope B550-2, User Manual

Share
Download
Skope B550-2 User Manual Download Page 12

12

Servicing

User Manual

SKOPE B550/660-2 and BME550-2

3

 Servicing

Isolating Electrics

The refrigeration unit can be totally isolated from the mains power, 
irrespective of whether the refrigerator is plugged into the mains. To achieve 
this, switch off the mains isolating switch and disconnect the refrigeration 
unit mains flex

To isolate the cabinet

1. Disconnect cabinet from the power supply.

2. Remove cabinet kick panel, by loosening the screws along top back 

flange of the kick panel. Raise the kick panel vertically to clear keyholes 
off the screw heads, then tilt panel forward and lift up and off the bottom 
fixing brackets. Access to top screws can be made easier by opening 
the cabinet doors.

3. Remove the controller from the kick panel, by loosening the two top 

fixing screws through the top slots in the kick panel.

4. Switch off isolating switch, and unplug refrigeration unit mains flex from 

the mains isolating box.

Figure 8:

Removing the Controller

Figure 9: Mains Isolating Box

Mains Isolating Box

Isolating Switch

Refrigeration Unit 
Mains Flex

Fixing Screws

Controller

Kick Panel

Summary of Contents for B550-2
















Reviews:

No comments

Brands by name

Popular brands

Load more brands