manualshive.com logo in svg

SKILTEC 9E DUETTE SKYLIFT POWERVIEW SYSTEM, Product Information Manual

Share
Download
SKILTEC 9E DUETTE SKYLIFT POWERVIEW SYSTEM Product Information Manual Download Page 4

PRODUCT INFORMATION MANUAL

SECTION: 9E DUETTE

®

 SKYLIFT POWERVIEW

®

 SYSTEM

ISSUE DATE: NOVEMBER 2017  

ORIGINATOR: SKILTEC 

REPLACES ISSUE DATE:  

APPROVED BY: R.BOKTOR 

PAGE 4 

Thank you for purchasing Luxaflex

®

 Duette

®

 SkyLift Shades. With proper installation, operation, 

and care, your new shades will provide years of beauty and performance.

Please thoroughly review this instruction booklet and the enclosed packing list before beginning 
the installation. 

Mounting Types

CAUTION:  

This shade cannot be installed as a “side stack” shade, operating from side-to-side 

within the window. Also, it cannot be installed as a “top-down” shade, where the fabric stack is 
at the bottom of the window.

Tools Needed 

 

■

 Allen Key (provided)

 

■

Level (laser level is recommended)

 

■

Measuring tape and pencil

 

■

Needle-nose pliers

 

■

Phillips screwdriver (magnetized screwdriver is recommended)

 

■

Power drill, 

3

/

32

" drill bit, and 

1

/

4

" hex key

 

■

Sharp scissors

 

■

Tape

Reveal Mount

Shade fits within

window opening

.

Face Mount

Shade mounts outside

window opening

.

Summary of Contents for 9E DUETTE SKYLIFT POWERVIEW SYSTEM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands