manualshive.com logo in svg

SKILTEC 9E DUETTE SKYLIFT POWERVIEW SYSTEM, Product Information Manual

Share
Download
SKILTEC 9E DUETTE SKYLIFT POWERVIEW SYSTEM Product Information Manual Download Page 25

PRODUCT INFORMATION MANUAL

SECTION: 9E DUETTE

®

 SKYLIFT POWERVIEW

®

 SYSTEM

ISSUE DATE: NOVEMBER 2017  

ORIGINATOR: SKILTEC 

REPLACES ISSUE DATE:  

APPROVED BY: R.BOKTOR 

PAGE 25 

Replacing the Batteries

Battery Wands

 

■

Raise the shade or lift the moving rail slightly.

 

■

Remove the cover from the bottom rail.

 

■

Unplug the battery wands from the power cable.

 

■

Remove the battery wands.

 

■

Open the battery wands and replace the batteries  
according to the label on the battery wands. 

 

■

Use 16 AA Lithium batteries.

 

■

Reinstall the battery wands in the bottom rail, plug in the power cable, and reinstall the 
bottom rail cover.

Satellite Battery Pack

 

■

Remove the battery wand cover.

 

■

Unplug the battery wand from the power cable.

 

■

Remove the battery wand from the wall mount 
bracket.

 

■

Open the battery wand and replace the batteries according to the label on the wand. 

 

■

Use 12 AA Lithium batteries.

 

■

Reinstall the battery wand into the wall mount bracket and plug in the power cable.

 

■

Replace the battery wand cover.

Summary of Contents for 9E DUETTE SKYLIFT POWERVIEW SYSTEM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands