4.
Safety
“READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (•) symbol listed
BELOW and other safety precautions, may result in serious personal injury.
•
cut only one workpiece at a time.
Multiple workpieces
cannot be adequately clamped or braced and may bind
on the blade or shift during cutting.
•
Be certain the flooring saw is mounted or placed on a
level, firm work surface before using.
A level and firm
work surface reduces the risk of the flooring saw
becoming unstable.
•
This tool is not equipped with provisions for
attaching an auxiliary fence.
Insure that the work piece
is supported by the fence before cutting.
•
plan your work. provide adequate support
accessories such as tables, saw horses, table
extension, etc. for workpieces wider or longer than
the table top.
Workpieces longer than the flooring saw
table can tip if not securely supported. If the cutoff piece
or workpiece tips it can lift the lower guard or be thrown
by the spinning blade.
•
Do not use another person as a substitute for a table
extension or as additional support.
Unstable support
for the workpiece can cause the blade to bind or the
workpiece to shift during the cutting operation pulling you
and the helper into the spinning blade.
•
The cutoff piece must not be jammed against or
pressured by any other means against the spinning
saw blade.
If confined, i.e. using length stops, it could
get wedged against the blade and thrown violently.
•
Always use a clamp or a fixture designed to properly
support round material such as dowel rods, or
tubing.
Rods have a tendency to roll while being cut,
causing the blade to “bite” and pull the work with your
hand into the blade.
•
When cutting irregularly shaped workpieces, plan
your work so it will not slip and pinch the blade and
be torn from your hand.
A piece of molding, for
example, must lie flat or be held by a fixture or jig that will
not let it twist, rock or slip while being cut.
•
let the blade reach full speed before contacting the
workpiece.
This will help avoid thrown workpieces.
•
if the workpiece or blade becomes jammed or
bogged down, turn flooring saw “off” by releasing
switch. Wait for all moving parts to stop and unplug
the flooring saw, then work to free the jammed
material.
Continued sawing with jammed workpiece
could cause loss of control or damage to flooring saw.
•
After finishing the cut, release the switch, hold the
saw arm down and wait for blade to stop before
removing work or cutoff piece. if blade does not stop
within ten (10) seconds, unplug the saw and follow
the instructions in the Troubleshooting section.
REACHING WITH YOUR HAND UNDER A COASTING
BLADE IS DANGEROUS!
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other
masonry products, and
• Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
•
There are additional safety instructions for particular
operations of the saw in the operating section. Read
the rest of the manual for safe operation.
locATioN
Use the flooring saw in a well lit area and on a level surface,
clean and smooth enough to reduce the risk of trips and falls.
Use it where neither the operator nor the casual observer is
forced to stand in line with the blade.
KicKBAcK
Kickbacks can cause serious injury: A “KICKBACK” occurs
when a part of the workpiece binds between the sawblade and
the rip fence or other fixed object. Workpiece binding the
blade due to misalignment, can also cause kickback. During
kickback, workpiece rises from table and is thrown toward the
operator. Keep your face and body to one side of the
sawblade, out of line with a possible “KICKBACK”.
KicKBAcKS AND poSSiBle iNJURY
cAN USUAllY Be AVoiDeD BY:
a.
Maintaining the rip fence parallel to the sawblade.
b.
Keeping the sawblade sharp. Replacing or sharpening anti-
kickback pawls when points become dull.
c.
Keeping sawblade guard, spreader and anti-kickback pawls
in place and operating properly. The spreader must
be in alignment with the sawblade and the pawls must stop
a kickback once it has started. Check their action before
ripping.
d.
NOT ripping workpiece that is twisted or warped or does not
have a straight edge to guide along the rip fence.
e.
NOT releasing work until you have pushed it all the way
past the sawblade.
WARNING
!
“SAVe TheSe iNSTRUcTioNS”
WARNING
!
Summary of Contents for 3600
Page 62: ...62 Notes ...
Page 63: ...63 Remarques Notas ...
