manualshive.com logo in svg

SKC 702-001, Operating Instructions Manual, Page: 5 / 36

Share
Download
SKC 702-001 Operating Instructions Manual Download Page 5

skcinc.com 

Form 37177 Rev 200910 

Page 5 

 

 
 
 

Attaching/Removing the Preamplifier 

To attach the preamplifier (

see below

), position the RED orientation key on the preamplifier with the RED 

identification mark on the sound level meter and gently push the preamplifier into the connector. 
 
To remove, gently pull the preamplifier stem away from the instrument body.  
 

 

 

 

 

 

 

 

 

 

 

 

 

Certifiable Calibration 

The calibration process includes the microphone, preamplifier and sound level meter. Any change in this 
measurement chain will require a new calibration certificate.  

SKC offers a complete calibration service offering a NIST calibration that can be supplied with or without 
a test report.  

It is recommended that your sound meter instrumentation is calibrated annually to ensure your measuring 
equipment is completely accurate and fully compliant

.  

 

Measuring Sound 

•

 

Always calibrate your SoundCHEK Essential sound level meter prior to and after taking 
measurements using an SKC AcoustiCHEK Calibrator Cat. No. 703 Series

. 

 

Sound Level 

– General Recommendations 

In some environments, high levels of noise can occur. The SoundCHEK Essential sound level meter has 
been designed for complete accuracy up to sound levels of 140 dB.  

Before you record measurements, take the time to ensure you have chosen the optimum range for the 
application. Wherever possible, the optimum range is when the average measured signal is 
approximately halfway between the top of the range and the bottom of the range without an overload 
condition.  

Preamplifier 

Microphone 

Only pull out and plug 
in the preamplifier. 
DO NOT TWIST

 

Summary of Contents for 702-001





































Reviews:

No comments