background image

SKAARHOJ Eth-SDI Link

Power over Ethernet (PoE) Speci

cations  

We use the PoE industry standard 48V IEEE 802.3af. If you want to power our controllers using PoE it is 
important your switch supports this standard. Please notice some manufactures such as Ubiquity have 
their own non-standard 24V type of PoE which is incompatible with our controllers. Especially pay 
attention to the standard if you use a PoE injector. 

Troubleshooting 

If you experience no network activity at all try one or more of the following suggestions: 

• Use a managed network switch 

• Force network switch port to 100 mbps 

• Try a different network switch 
1GB or 10 GB switches can have issues with our 100 mbps interface if not properly managed. The iMac 
Pro with 10 GB have issues if connected directly to our controller. Try with a USB to ethernet adapter in this 
case. 

WEEE Information 

For private households: Information on Disposal for Users of WEEE  

This symbol (figure 1) on the product(s) and / or accompanying documents means that used electrical and electronic equipment 

(WEEE) should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product(s) 

to designated collection points where it will be accepted free of charge.  

Alternatively, in some countries, you may be able to return your products to your local retailer upon purchase of an equivalent new 

product.  

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and 

the environment, which could otherwise arise from inappropriate waste handling.  

Please contact your local authority for further details of your nearest designated collection point.  

Penalties may be applicable for incorrect disposal of this waste, in accordance with you national legislation. 

For professional users in the European Union  

If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or supplier for further information. 

For disposal in countries outside of the European Union  

This symbol is only valid in the European Union (EU). If you wish to discard this product please contact your local authorities or 

dealer and ask for the correct method of disposal.

12

Figure 1

Summary of Contents for ETH-SDI













Reviews: