background image

 

Molenvliet 28 

3961 MV Wijk bij Duurstede 

+31 343 595 400 

www.sitetec.nl [email protected] 

 

 

 

In all cases in which we act as offerer or supplier, our offers, assignments given to us and agreements concluded with us are subject to the METAALUNIE 

TERMS AND CONDITIONS. These terms and conditions have been filed at the Registry of the Rotterdam District Court. The Dutch law is applicable on all 

our agreements. KVK nr. 34043947 | VAT/BTW nr. NL.0034.76.443.B01 |  IBAN NL94ABNA 0565320300

 

 

1.3 

OVERALL CHECK OF THE MIXING UNIT 

 
Before you start mixing there are several checks to be made: 
 

1.

 

Check for debris in the mixing tank. Tank must be clean 

2.

 

Put 2 pump strokes of high quality bearing grease in all nipples on the AMTEQ pumps 

3.

 

Check if all electrical cables and wires are still in good condition, repair if necessary 

4.

 

Check, overall, for any damaged or loose parts and repair if needed 

5.

 

Check all guards 

6.

 

Check the tank for cracks 

 

1.4  

CAPACITY PARAMETERS   

 

This unit is capable of mixing 500 ltr/min with fresh water, 7 ph and up to 60 sec of viscosity. 
  

2.1  

VALVE SCHEDULE 

 

1.

 

Suction valve mix tank to pump 

2.

 

Discharge from pump to venturi 

3.

 

Discharge from pump to tank nozzles 

4.

 

Discharge from pump to outlet 

5.

 

Outlet to drain tank 

6.

 

Hopper inlet valve dry bentonite 

7.

 

Water inlet valve to mix and water tank 

8.

 

Bleed valve 

9.

 

Suction from water tank, only at dual tank model 

 

 

 

 

Summary of Contents for M405D









Reviews: