Document NO.:RD-519-39-001
Version: A 2018.04.20
- 3 -
6.
In insect-infested areas.
7.
Smoke alarms should not be installed within 3 ft (0.9m) of
the following: the door to a kitchen, the door to a bathroom
containing a tub or shower, forced air supply ducts used for
heating or cooling, ceiling or whole house ventilating fans,
or other high air flow areas.
8.
Kitchens. Normal cooking may cause false alarms. If a
kitchen alarm is desired, it should have an alarm silence
feature or be a photoelectric type.
9.
Near fluorescent lights. Electronic “noise” may cause false
alarms.
10.
Smoke alarms are not to be used with detector guards.
Unless the combination (alarm and guard) has been
evaluated and found suitable for that purpose.
Operation:
Testing:
Test the unit to ensure proper operation by pressing the Test
button for at least 5 seconds, this will sound the alarm if the
electronic circuitry, horn and battery are working properly. If
no alarm sounds, the unit has a defective battery or other
failure. Refer to “Trouble shooting” section for a solution.
DO NOT use an open flame to test your alarm, you could
damage the alarm or ignite combustible materials and result
in a fire.
CAUTION:
Due to the loudness (85 decibels) of the alarm,
always stand an arm-length away from the unit when testing.
Test the alarm weekly to ensure proper operation. Erratic or
low sound coming from your alarm may indicate a defective
alarm
NOTE: WEEKLY TESTING IS REQUIRED.
LED indicators:
Illumination of the Green LED indicates that the alarm is
receiving AC power.
This alarm equipped with the red LED indicator indicates
two operation modes.
Red LED-Flashing every 32 seconds: indicates that the
smoke alarm is operating properly.
RED LED-Flashing: when the Test button is pressed or the
smoke alarm sense particles of combustion and go into alarm
(constant pulsating sound), the red LED will flash once per
second. The flashing LED and pulsating alarm will continue
until the test button is released or the air is cleared.
RED LED-Alarm silencer (Hush mode) indication: The red
LED will flash every 8 seconds, indicating the smoke alarm
is in the alarm silencer (Hush) mode.
NOTE: WEEKLY TESTING IS REQUIERED.
Alarm silence (hush mode):
When you press same Test button for at least 5 seconds (or
until the unit sounds) to active silence control, the alarm will
enter HUSH mode for approx. 8 minutes. Smoke alarms are
designed to minimize false alarms. Combustion particles
from cooking may set off alarm if the alarm is located close
to cooking area. Large quantities of combustible particles are
generated from spills or when grilling/frying. Using the fan
on a range hood that vents to outside (non-recirculation type)
will also help remove these combustible particles from the
kitchen. The alarm silence (test button) is extremely useful in
a kitchen area or other areas prone to nuisance alarms.
The alarm silence (hush mode) has the capability of
temporarily forbid the alarm circuit to detect smoke for about
8 minutes. This feature is to be used only when a known
alarm condition, such as smoke from cooking, activates the
alarm.
The smoke alarm will automatically reset after approximately
8 minutes. The alarm will sound again 8 minutes later if
combustible particles are still present.
The alarm silencer (hush mode) can be repeated until the air
has been cleared.
CAUTION:
Before using the alarm silence (hush), identify
the source of the smoke and be certain a safe condition exists.
DANGER:
If the alarm sounds, and it is not being tested, it
means the unit is sensing smoke,
THE SOUND OF THE
ALARM REQUIRES YOUR IMMEDIATE ATTENTION AND
ACTION.
①
Take out one unit from all units, press the wireless test
button 3 times within 2 seconds to enter “Learning mode “.
The red LED lighting 2 minutes indicates operation success.
Wireless function description:
Wireless frequency:
433.42MHz
Operation current:
RF Receiver:
<9mA
RF emitter:
<30 mA
Wireless interconnection:
up to 40 detectors
Wireless distance:
>100 meters in free field
/
30m indoors
Warning
: wireless bases use coded RF signals and need to
be paired before use.
1: Establish wireless connection between smoke
alarms
Note:
Before operation, the unit must be in normal working
mode.
NOTE:
Products can be learned repeatedly, but all products
must be studied with the same product. Please remember this
