background image

 

10 

Stopping the Engine   

In an emergency:

   

To stop the engine in an emergency, move the engine switch to the OFF position.   

In normal use: 

 

1. Turn the AC circuit breaker to the OFF position.     
2. Turn the engine switch to the OFF position.   
3. Turn the fuel valve lever to the OFF position.   

OPERATING INSTRUCTIONS 

Connections to a Building Electrical System   

Connections  for  standby  power  to  a  building  electrical  system  must  be  made  by  a  qualified 
electrician. The connection must isolate the generator power from utility power, and must comply 
with  all  applicable  laws  and  electrical  codes.  A  transfer  switch,  which  isolates  generator  power 
from utility power, is prerequisite.   

WARNING: 

tility  company  workers  or  others  who  contact  the  lines  during  a  power  outage,  and  the  generator 
may  explode,  burn,  or  cause  fires  when  utility  power  is  restImproper  connections  to  a  building 
electrical system can allow electrical current from the generator to back feed into the utility lines. 
Such back feed may electrocute uored. Consult the utility company or a qualified electrician.   
 

Connection Notes 

  Avoid connecting the genetor to commercial power outlets

This is a single phase generator only

 

                  Avoid connecting the generator in parallel with any other generator

 

Ground System   

The  portable  generators  have  a  system  ground  that  connects  generator  frame  components  to  the 
ground terminals in the AC output receptacles. The system ground is not connected to the AC neutral 
wire.   
Make  sure  you  connect  a  proper  ground  (earth)  to  the  generator. 

You  should  use  the  ground 

terminal on the front panel of the generator and a stake at the end of uncovered copper ground 
wire driven into soil.This completes a safe natural ground circuit. 

  Ground(earth) Lead 
  Diameter: 
          0.12mm(0.005in) per (ampere) Amp 

 

EXAMPLE: 

      10(Ampere) Amps

1.2mm

0.05in

 

AC Applications   

B

efore connecting an appliance or power cord to the generator:   

Make sure that it is in good working order. Faulty appliances or power cords can create a potential for 
electrical shock.   
If  an  appliance  begins  to  operate  abnormally,  becomes  sluggish  or  stops  suddenly,  turn  it  off 
immediately. Disconnect the appliance, and determine whether the problem is the appliance, or if the 
rated load capacity of the generator has been exceeded.   

Summary of Contents for SPG8000



















Reviews: