Sitecom WLR-6000 User Manual Download

Page: 31 / 86

E |3

Data Rate

The “Data Rate” is the rate that this access point uses to transmit

data packets. The access point will use the highest possible selected

transmission rate to transmit the data packets.

N Data Rate

The “Data Rate” is the rate that this access point uses to

transmit data packets for N compliant wireless nodes. Highest to lowest data

rate can be fixed.

Channel Bandwidth

is the range of frequencies that will be used.

Preamble Type

The “Long Preamble” can provide better wireless LAN

compatibility while the “Short Preamble” can provide better wireless LAN

performance.

Broadcast ESSID

If you enabled “Broadcast ESSID”, every wireless station

located within the coverage of this access point can discover this access point

easily. If you are building a public wireless network, enabling this feature is

recommended. Disabling “Broadcast ESSID” can provide better security.

CTS Protection:

It is recommended to enable the protection mechanism.

This mechanism can decrease the rate of data collision between 802.11b and

802.11g wireless stations. When the protection mode is enabled, the

throughput of the AP will be a little lower due to a lot of frame-network that is

transmitted.

TX Power

can be set to a bare minimum or maximum power.

WMM

WiFi Multi Media if enabled supports QoS for experiencing better audio,

video and voice in applications.

Summary of Contents for WLR-6000























































































Search results

Summary of Contents for WLR-6000

Reviews:

Related manuals for WLR-6000

Brands by name

Popular brands

Sitecom WLR-6000, User Manual

Search results

Summary of Contents for WLR-6000

Reviews:

Related manuals for WLR-6000

Brands by name

Popular brands