Sitecom WLM-2501 User Manual Download | Manualshive

Page: 36 / 67

background image

protection mode is enabled, the throughput of the AP
will be a little lower due to many of frame traffic should
be transmitted.

Aggregation

This function is used to join multiple data packets for
transmission as a single unit to increase network
efficiency.

Short GI

The 802.11n draft specifies two guard intervals: 400ns
(short) and 800ns (long). Support of the 400ns GI is
optional for transmit and receive. Enable this function
will increase network efficiency.

When you finish, click ‘Apply Changes’. You’ll see the following message
displayed on web browser:

Press ‘Continue’ to save the settings made and back to web management
interface; press ‘Apply’ to save the settings made and restart the router so the
settings will take effect after it reboots.

«
...
34
35
36
37
38
...
»

Summary of Contents for WLM-2501




































































Reviews:

No comments

Related manuals for WLM-2501

Brand: Dali Pages: 8

DWL-2700AP - AirPremier Outdoor Wireless Access...

Brand: D-Link Pages: 70

DWL-2200AP - AirPremier - Wireless Access...

Brand: D-Link Pages: 58

Brand: Xylem Pages: 20

Brand: H3C Pages: 43

LtAP RB912R-2nD-LTm&R11e-4G

Brand: MikroTik Pages: 7

Brand: HABITECH Pages: 3

JBLLIVEFRNCPTWSB

Brand: JBL Pages: 40

Brand: Aruba Pages: 2

YLS0056A-E080040

Brand: THOMSON Pages: 38

Brand: OBERON Pages: 2

Brand: Arista Pages: 4

WLTMS-110_384041

Brand: Gemtek Systems Pages: 14

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 6

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands