WEA463e Quick User Guide
Base
Console Port, Factory Reset Switch
Ethernet Port (PoE)
DC Input
Ethernet Port
Backhaul LED
LED Status
Indicator
Interface
Interface
Description
LED Status
Displays the status information of WEA463e using an LED.
DC Input
Connects the power adaptor.
Ethernet Port
(PoE)
Supports a 1000 BASE-T Gigabit Ethernet and PoE IEEE
802.3af/802.3at connection.
Console Port
Used to check the operational status of the WEA463e and to input the CLI.
Factory
Reset Switch
Used to switch the WEA463e to the initial factory settings.
LED Status Indicator
LED
Status
Description
System Start
White
Initial LED status
Blue
Device reset and diagnostic test in
progress
Red
Booting failure (device reset failure)
Provisioning
Repeating red and green
Connecting APC (network link normal)
Blinking green
Connecting CAPWAP (APC server
connection status normal)
Normal
Operations
Green
No wireless UE connected
Blue
Wireless UE connected
Upgrade
Blinking blue
Upgrading software
Failure
Blinking red
Network connection failure (physical)
Blinking orange
IP address conflict
Blinking violet
Dynamic IP address allocation failure
Blinking bluish green
Network connection failure (logical)
Repeating Red and Blue
Wireless interface failure
Backhaul LED
LED
Stuatus and description
Connection Ready
White LED On
Connection Complete
If connected with AP, LED blinks red, white, green, blue color
sequentially according to signal strength.
※
LED turns off when it does not configured for Mesh AP.
Installation
The WEA463e can be installed on a pole or on a wall.
Please confirm that all of the components have been included before installation.
Install the product in a vertical position and ensure that I/O ports are facing down.
Before Installation
Safety Requirements
Carefully observe the following safety warnings in order to avoid the risk of
damage or injury. Always follow these safety precautions when using the product.
- There is a risk of electrical shock. Make sure that the
power is turned off during installation. Do not proceed with
the installation if there is any electrical current leaking.
It may cause a serious electric shock.
- Wear anti-static gloves or take an appropriate action to
prevent ESD when handling the product.
- Do not connect a phone line to an Ethernet port.
This may damage the product.
- This product must be connected to a power supply in
compliance with IEEE 802.3af/at or connected to a limited
power supply in compliance with IEC/EN/UL 60950-1.
- This product must be installed or removed by only
appropriately trained service personnel.
- For outdoor use or installation outdoors. For more details,
refer to “Environment” in the IEEE 802.3af/at standards.
- This product must be installed at least 3 m or further away
from a WiBro/3G/4G repeater or antenna.
This manual describes the Wireless Enterprise WEA463e
configuration and installation instructions.
Introduction
What is WEA463e?
The WEA463e is an 802.11ac-based outdoor Wireless Enterprise AP that
supports Mesh Networking. It connects the UE that supports wireless LAN,
such as a smartphone, tablet, or notebook, to a wired network in an outdoor
environment.
The WEA463e supports the following features:
- IEEE 802.11a/b/g/n/ac standard
- Power over Ethernet (PoE) IEEE 802.3af/802.3at
- 3 × 3 Multiple Input Multiple Output (MIMO)
- Wireless LAN through both 2.4 GHz and 5 GHz bandwidths
- Temperature Range: -40~+55°C
- Environment Condition: IP66 & IP67
Components
After unpacking the WEA463e, confirm that all of the following items have been
included:
Front
Rear
Common Components
Mount, Unit Bracket
Waterproof Connector
for Ethernet Cable, Installation Guide
6 M4 × L10 Screws
Quick Start Guide
Wall-Mount Installation Materials
5 plastic Anchors
5 M4 × L25 Screws
It is recommended that you keep the box and all of the
packing materials.
Name and Function
Side
Ground Wire
