manualshive.com logo in svg

Sitecom WLM-1500, User Manual, Page: 62 / 67

Share
Download
Sitecom WLM-1500 User Manual Download Page 62

 

Remote Access 

 
The Remote Access function can secure remote host access to your router from 
LAN and WAN interfaces for some services provided by the router. These 
services include Telnet, FTP, TFTP, HTTP, SNMP and PING. 
 
Please click ‘System’ menu on the left of web management interface, then click 
‘Remote Management’, and the following page will be displayed on your web 
browser: 
 

 

 

Parameter 

Description

 

LAN 

Check/un-check the services on the LAN column to allow/un-
allow the services access from LAN side. 

WAN 

Check/un-check the services on the WAN column to allow/un-
allow the services access from WAN side. 

WAN Port 

This field allows the user to specify the port of the 
corresponding to the service. Take the HTTP service for 
example; when it is changed to 8080, the HTTP server address 
for the WAN side is 

http://dsl_addr:8080

, where the “dsl addr” 

is the WAN side IP address of the router. 

 
When you finish, click ‘Apply Changes’. You’ll see the following message 
displayed on web browser: 
 

 

 

Summary of Contents for WLM-1500




































































Reviews:

No comments