Sitecom WL-347 User Manual Download

Page: 9 / 59

N System Requirements

To begin using the WL-347/WL-348, make sure you meet the following

as minimum requirements:

•

PC/Notebook.

•

Operating System – Microsoft Windows XP/2000/VISTA

•

1 Free Ethernet port.

•

Wi-Fi card/USB dongle (802.11 b/g/n) – optional.

•

Annex A, ADSL internet connection.

•

PC with a Web-Browser (Internet Explorer, Safari, Firefox, Opera)

•

Ethernet compatible CAT5 cables.

WL-347/WL-348 Placement

You can place the WL-347/WL-348 on a desk or other flat surface, or

you can mount it on a wall. For optimal performance, place your

Wireless Broadband Modem/Router in the center of your office (or your

home) in a location that is away from any potential source of

interference, such as a metal wall or microwave oven. This location

must be close to a power connection and the ADSL/phone line should

not be over 2 meters long.

Summary of Contents for WL-347




























































Search results

Summary of Contents for WL-347

Reviews:

Related manuals for WL-347

Brands by name

Popular brands

Sitecom WL-347, User Manual

Search results

Summary of Contents for WL-347

Reviews:

Related manuals for WL-347

Brands by name

Popular brands