Sisu Commercial Products Sleeptight 800 Owner'S Manual And Instructions Download | Manualshive

Page: 9 / 41

background image

HANDLE INSTALLATION

1. Assemble handle together using the provided spacers and 5/16-18 x 1 3/4” bolts. See figure below for

details.

2. Secure the handle to the heater with provided bolts, 5/16-18 x 1 3/4”.

HOSE HANGER

• Install the hose hanger to the side of the heater with the provided 1/4-20 x 3/4” bolts and 1/4 flat washers.

See previous figure.

FRESH AIR MODULAR HANGER

• Install the stand off screws to the heater as shown in the figure above.

• Aft er tightening the Stand-Off screws, there will be a space between the screw head and the case to hang

the fresh air module.

8

NOTE: Ensure handles are

positioned as shown.

Flat Washer

Bolt

Stand-Off Screw

Spacer

«
...
7
8
9
10
11
...
»

Summary of Contents for Sleeptight 800










































Reviews:

No comments

Related manuals for Sleeptight 800

Brand: Harry Taylor Pages: 56

Brand: Vanguard Pages: 14

Brand: Harry Taylor Pages: 52

Brand: KASTOR Pages: 40

Brand: Icom Pages: 16

IC-FR4000 Series

Brand: Icom Pages: 20

Brand: Vagner Pool Pages: 35

Brand: A.O. Smith Pages: 4

AQUA PLUS 200 LT

Brand: Ferroli Pages: 96

Brand: Modine Manufacturing Pages: 28

Brand: usha Pages: 8

DynaFLO DOWB-S1 Series

Brand: Camus Hydronics Pages: 28

Brand: Dancover Pages: 7

Brand: Somogyi Pages: 20

Brand: SOLARFOCUS Pages: 52

Brand: ARDES Pages: 28

Brand: pyromaster Pages: 20

Brand: Laars Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands