sisel ENDA ET4430 Manual Download Page 1

Page: 1 / 7

EN 60584

DIN 43710

EN 60584

EN 60584
EN 60584

EN 60751
EN 60751

°C

°F

-199.9...600.0

-30.0....600.0°C

-30.0...999.9°C

-30.0...400.0°C

-200...600

-30....600°C

-30...1300°C

-30....400°C

-40...1700°C
-40...1700°C

°C

-22.0....999.9 °F

-22.0....752.0 °F

-199.9...999.9

-22....2372 °F

-22......752
-40....3092

-40....3092

-328....1112

-22....1112 °F

°F
°F
°F

°F

ET4430-EN-01-190116

SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.

Şerifali Mah.

Y.Dudullu 34775

ÜMRANİYE/İSTANBUL-TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr

Barbaros Cad. No:18

1/4

DIN 43710

ENDA

ET4430

PID

TEMPERATURE

CONTROLLER

Thank you for choosing

ENDA

ET4430

Temperature

ontroller

Devices

Please read this document carefully before using this product. The guarantee will be invalidated if the device is damaged by not following instructions
detailed in the manual. The company shall not be responsible for any damage or losses however caused, which may be experienced as a result of the
installation or use of this product.

Input Type

Scale Range

J (Fe-CuNi)

Thermocouple

L (Fe-CuNi)

Thermocouple

J (Fe-CuNi)

Thermocouple

L (Fe-CuNi)

Thermocouple

K (NiCr-Ni)

Thermocouple

K (NiCr-Ni)

Thermocouple

T (Cu-CuNi)

Thermocouple

T (Cu-CuNi)

Thermocouple

S (Pt10Rh-Pt) Thermocouple
R (Pt13Rh-Pt) Thermocouple

PT100 Resistance Thermometer
PT100 Resistance Thermometer

0,5% (for full scale)

1 digit

0,5% (for full scale)

1 digit

0,5% (for full scale)

1 digit

0,5% (for full scale)

1 digit

0,2% (

)

for full scale

1 digit

0,2% (

)

for full scale

1 digit

Accuracy

ENVIRONMENTAL CONDITIONS

Height

Ambient/storage temperature
Max. Relative humidity
Rated pollution degree

ELECTRICAL CHARACTERISTICS

Supply
Power consumption
Wiring
Line resistance
Data retention

EMC
Safety requirements

OUTPUTS

A1 Output

Life expectancy for relay

C/A2 Output

SSR Output

ONTROL

ontrol

type

Control algorithm
A/D

converter

Sampling time
Proportional band
Control period

Hysteresis

Output power

HOUSING

Housing type

Dimensions

Weight
Enclosure material

90-250V AC 50/60Hz,

or 9-30VDC / 7-24VAC

%10 SMPS

24V AC ±%10 50/60Hz

Max. 5VA
Power screw-terminal connections: 2.5mm²', Signal screw-terminal connections: 1,5mm².

EN 61326-1: 2013 (Performance criterion B satisfied for EN 61000-4-3 standard).

EEPROM (minimum 10 years)

Max.

100

EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)

Suitable for flush-panel mounting according to DIN 43 700.

W48xH48xD87mm

Approx. 250g
Self extinguishing plastics

Single Setpoint and Alarm Control.

On-Off / P, PI, PD, PID selection.
14

bit

Min. 1

00ms

Can be adjusted between

and

%100

.0 . If

Pb=%0

, ON

OFF

ontrol

is selected.

Can be adjusted between

and 125secs.

Can be adjusted between 1 and 50°C/F.
Setpoint value ratio can be adjusted between %0 and %100 .

Relay : 250V AC, 8A (for resistive load), NO+NC (Control or Alarm2 Output selection).

Relay : 250V AC, 8A (for resistive load), NO (Alarm1 and Cooling Control Output selection).

Max.

2000m

0 ... +50°C/-25 ... +70°C

According to EN 60529; Front panel : IP6

Rear panel : IP20

Max. SSR Output ; 24V 20mA.

Relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C.

Without load 30.000.000 switching; 250V AC,

A (resistive load) 300.000 switching.

KEEP AWAY device from exposed to corrosive, volatile and flammable gases or liquids and DO NOT USE the device in similar hazardous locations.

Avoid any liquid contact when the device is switched on.
DO NOT clean the device with solvent (thinner, gasoline, acid etc.) and / or abrasive cleaning agents.

Self tune for automatic PID calculation or
manually enter PID parameters if known.

Three different feature can be assigned to digital input.
Three different feature can be assigned to F function key.
Soft-Start feature.
SSR or Relay Output Control selection.
A1 Relay output

programmable

as primary Alarm or PID Cooling Control output.

C/A2 Relay output can be used as secondary Alarm or Temperature Control output.
Heating/Cooling control selection.

Zero point input shift

In case of sensor failure, periodically, auto-periodically running or relay state can be selected.
RS485 Modbus RTU communication protocol feature (Specify at order).
CE marked according to European Norms.

48x48mm sized.

PT100 ,J, K, L, T, S, R sensor types can be selected.

Dual setpoint value can be selected.

Auto calculation for PID parameters (SELF TUNE).

Order Code : ET4430

1 -

     230VAC...90 - 250V AC
     24VAC.....24V AC
     SM...........9-30V DC /
                      7-24V AC

Supply Voltage

RS.....

...

RS-485

Blank