background image

16

WORKING

Remote control (Fig.12)

channel radio control for cooker hood remo-

te.

At  first  ignition,  keep  pressed  the  lighting 

button for 5 seconds.

RC001

R

ADIO

 C

ONTROL

Radio control used for the remote operation 

of ducted cooker hoods.

TECHNICAL DATA

- Alkaline battery powered: 12 V mod. 23 A

- Operating frequency: 433.92 Mhz

- Combinations: 32.768

- Max. consumption: 25 mA

- Operating temperature: -20 ÷ + 55 °C

- Dimensions: 120 x 45 x 15 mm.

OPERATING DESCRIPTION

The  transmitter  is  equipped  with  5  buttons 

for  cooker  hood  management,  as  specified 

below:

 

: Light ON/OFF command.

 

: Motor ON (speed level 1) / OFF command.

 

: Reduce speed.

 

: Increase speed.

 

: 10-minute timer.

The set suction speed is indicated by the LED 

in the suction perimeter channel.

To each color generated by the LED, it cor-

responds a specific speed, as shown below:

First speed WHITE

Second speed BLUE

Third speed DARK BLUE

Fourth speed RED

INITIAL OPERATING CONDITION

The manufacturer supplies the radio control 

unit ready to be used with codes preset in the 

Factory

OPERATION MODE 

Standard configuration:

Standard  configuration  requires  all  “cooker 

hoods  –  radio  control  -  system”  to  be  pro-

vided  with  the  same  transmission  code.  In 

the  event  two  cooker  hoods  –  radio  control 

system are installed in the same room or ne-

arby, each system may affect the operation of 

the another. Therefore, the code of one radio 

control system must be changed.

Generatiing a new transmiissiion code:

The  radio  control  system  is  provided  with 

preset  codes.  Should  new  codes  be  requi-

red, proceed as follows: Press simultaneously 

buttons:

for  two  seconds.  When  Leds  light  on,  press 

buttons: 

(within 5 seconds). Leds flashing 3 times in-

dicate

the procedure is completed.

WARNING! This  operation deletes  perma-

nently the preset codes.

Learniing the new transmiissiion code:

Once the transmission code is changed in the 

radio control unit, the electronic central unit 

of the cooker hood must be made to set the 

new code in the fol- lowing way:

Press the main power-off button of the hood 

and then restore power to the electronic con-

trol unit. Within the next 15 seconds, press 

the Liight Button        to synchronise the cen-

tral unit with the code.

Reset of the Factory confiiguratiion:

To  restore  the  Factory  configuration,  follow 

the  pro-  cedure  described  below:  press  si-

multaneously buttons:

for 2 seconds. When Leds light on, press but-

tons:

Summary of Contents for SLT105























Reviews: