54
PARTS LIST - 01708
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
1.
Base
WD02-00329
34.
Lock handle
WD02-00352
2.
Column flange
WD02-00330
35.
Label
WD02-00353
3.
Spring washer M10
WD01-00795
36.
Connection
WD02-00354
4.
Bolt (M10 x 35)
WD02-00331
37.
Pinion shaft
WD02-00355
5.
Crank handle
WD02-00332
38.
Indicator
WD01-00897
6.
Bolt (M6 x 12)
WD01-00905
39.
Screw
WD02-00356
7.
Circlip
WD01-00742
40.
Roll pin (5 x 25)
WD01-00869
8.
Worm shaft
WD02-00333
41.
Screw (M10 x 10)
WD02-00345
9.
Table support
WD02-00334
42.
Bearing 6005
WD01-00889
10.
Worm pin
WD02-00335
43.
Warning label
WD01-00685
11.
Table
WD02-00431
44.
Roll pin (6 x 18)
WD01-00760
12.
Spring washer M20
WD02-00337
45.
Belt tension handle
WD02-00358
13.
Bolt (M20 x 55)
WD02-00338
46.
Lock handle
WD02-00359
14.
Indicator
WD01-00897
47.
Circlip
WD01-00816
15.
Lock handle
WD02-00339
48.
Circlip
WD01-00871
16.
Angle label
WD02-00340
49.
Adjusting shaft
WD01-00872
17.
Worm gear
WD02-00341
50.
Shaft
WD02-00360
18.
Column
WD02-00342
51.
Washer M12
WD01-00819
19.
Rack
WD02-00343
52.
Washer M10
WD02-00361
20.
Hex. wrench 3mm
WD01-00790
53.
Nut M8
WD01-00687
21.
Hex. wrench 4mm
WD01-00737
54.
Motor plate
WD02-00362
22.
Screw (M10 x 10)
WD02-00345
55.
Bolt (M8 x 30)
WD02-00363
23.
Hex. wrench M5
WD02-00397
56.
Spring washer M12
WD01-00676
24.
Hex. wrench M6
WD01-00861
57.
Nut M12
WD01-00821
25.
Rack collar
WD02-00346
58.
Motor
WD02-00428
26.
Screw (M6 x 12)
WD01-00740
59.
Grub screw (M8 x 10)
WD01-00689
27.
Handle knob
WD02-00347
60.
Motor pulley
WD02-00365
28.
Screw (M6 x 12)
WD01-00740
61.
Motor pulley key
WD02-00366
29.
Handle cap
WD02-00349
62.
Nut M10
WD01-00717
30.
Screw (M8 x 20)
WD01-00801
63.
Belt A787
WD02-00367
31.
Spring washer M8
WD01-00673
64.
Microswitch
WD01-00706
32.
Handle
WD02-00350
65.
Washer M5
WD01-00881
33.
Scale
WD02-00351
66.
Spring washer M5
WD01-00882
7
Remove the key from the chuck after adjustment.
Use only the chuck key provided by the manufacturer or a duplicate of it.
Appropriate personal protective equipment
MUST
be worn and
MUST
be designed
to protect against all hazards created. Severe permanent injury can result from
using inappropriate or insufficient protective equipment - Eyes in particular are at
risk.
Do not overload the tool. Allow the tool to operate at its optimum speed for maxi-
mum efficiency.
Always ensure that the accessories such as drill bits, as well as the drill are rated /
designed for use with required application, and are the bits are correctly and se-
curely fastened before connecting the tool to the mains supply.
The work must be clamped firmly while drilling. Any tilting, twisting or shifting results
not only in a rough hole but also increases the hazard, which could result in injury or
drill breakage. For flat work lay the piece on a wooden base and clamp it firmly
down against the table to prevent it from turning If the piece is of irregular shape
and cannot be laid flat on the table, it should be securely blocked and clamped.
Understand the operating environment;
Before each use the operator should as-
sess, understand and where possible reduce the specific risks and dangers associ-
ated with the operating environment. Bystanders should also be made aware of
any risks associated with the operating environment.
SAFETY INSTRUCTIONS….cont
When using the pillar drill for certain operations, particularly during ex-
tended periods; ensure the operator as well as those in the area wear
ear protection.
When using the pillar drill always ensure the operator as well as those in
the area wear eye protection.
Some materials have the potential to be highly toxic; always wear a
face mask when operating the pillar drill.
CAUTION:
The warnings and cautions mentioned in this user manual can not cover all possible
conditions and situations that may occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into this product, but must be applied.