42
PARTS LIST - 01704
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
1.
Base
WD01-00793
35.
Washer M8
WD01-00672
2.
Column flange
WD01-00794
36.
Motor plate
WD01-00820
3.
Spring washer M10
WD01-00795
37.
Nut M12
WD01-00821
4.
Bolt (M10 x 25)
WD01-00796
38.
Grub screw (M8 x 10)
WD01-00689
5.
Rack
WD02-00280
39.
Motor pulley
WD01-00822
6.
Column
WD02-00281
40.
Motor
WD01-00823
7.
Screw (M6 x 12)
WD01-00740
41.
Spring washer M12
WD01-00676
8.
Rack collar
WD01-00799
42.
Nut M8
WD01-00687
9.
Screw (M6 x 16)
WD01-00708
43.
Cam pin
WD01-00824
10.
Handle cap
WD01-00800
44.
Cam
WD01-00825
11.
Screw (M8 x 20)
WD01-00801
45.
Washer
WD01-00826
12.
Spring washer M8
WD01-00673
46.
Speed label
WD01-00827
13.
Handle knob
WD01-00802
47.
Nut M5
WD01-00697
14.
Handle
WD01-00803
48.
Pulley cover
WD01-00828
15.
Knob
WD01-00804
49.
Washer M6
WD01-00702
16.
Scale
WD01-00805
50.
Microswitch
WD01-00706
17.
Connection
WD01-00806
51.
Washer M6
WD01-00702
18.
Label
WD01-00807
52.
Spring washer M6
WD01-00707
19.
Roll pin (5 x 18)
WD01-00808
53.
Screw (M6 x 16)
WD01-00708
20.
Pinion shaft
WD01-00809
54.
Microswitch holder
WD01-00709
21.
Warning label
WD01-00685
55.
Nut M6
WD01-00710
22.
Roll pin (6 x 18)
WD01-00760
56.
Eccentric shaft
WD01-00829
23.
Indicator
WD01-00811
57.
Centre pulley
WD01-00830
24.
Belt tension handle
WD01-00812
58.
Bearing 6202
WD01-00771
25.
Circlip
WD01-00813
59.
Circlip
WD01-00831
26.
Locking handle
WD01-00814
60.
Belt O-500
WD01-00832
27.
Roll pin (6 x 18)
WD01-00760
61.
Belt O-565
WD01-00833
29.
Screw (M5 x 10)
WD01-00726
62.
Spindle pulley
WD01-00834
30.
Circlip
WD01-00816
63.
Circlip
WD01-00713
31.
Shaft
WD01-00817
64.
Spindle shaft
WD01-00835
32.
Adjusting shaft
WD01-00818
65.
Bearing 6203
WD01-00714
33.
Washer M12
WD01-00819
66.
Knurled screw
WD01-00836
34.
Bolt (M8 x 25)
WD01-00695
67.
Circlip
WD01-00704
19
ASSEMBLY INSTRUCTIONS….cont
Carefully raise the head above the column.
Ensure that the hole in the bottom of the drill
head lines up with the column.
Lower the drill head down the column taking
care that the head and the column stay
square with each other.
Line up the spindle with the table and base
(011).
Secure in place by tightening the 2 x grub
screws on each side (012).
FIT THE FEED HANDLE - 01700 & 01701
To fit the feed handles; simply screw them
into the hub, as shown (013).
FIT THE FEED HANDLE - 01702 - 01708
Fit the cast feed handle over the hub.
Secure in place by tightening the 3 x screws, as
shown (014).
011
012
013
014
