manualshive.com logo in svg

Sinclair SWH-200IRA2, User Manual, Page: 50 / 52

Share
Download
Sinclair SWH-200IRA2 User Manual Download Page 50

Air Source Heat Pump Water Heater

 

45 

  Please contact the SINCLAIR appointed service center in case of any of

following conditions. 

Malfunction phenomenon 

Malfunction analysis 

The water heater stops operation and 
the wired controller displays PF 

Malfunction of temperature sensor of 
drive electric box of inverter 
compressor   

The water heater stops operation and 
the wired controller displays P9 

Zero-crossing protection of drive AC 
input of inverter compressor   

The water heater stops operation and 
the wired controller displays AL 

Low voltage protection of drive DC bus 
bar of inverter outdoor unit or voltage 
dropping malfunction   

The water heater stops operation and 
the wired controller displays AH 

High voltage protection of drive DC bus 
bar of inverter outdoor unit   

The water heater stops operation and 
the wired controller displays AA 

AC current protection of inverter 
outdoor fan (input side)   

The water heater stops operation and 
the wired controller displays A1 

Drive IPM module protection of inverter 
outdoor fan   

The water heater stops operation and 
the wired controller displays AF 

Drive PFC protection of inverter outdoor 
fan   

The water heater stops operation and 
the wired controller displays AC 

Failure startup of inverter outdoor fan   

The water heater stops operation and 
the wired controller displays Ad 

Phase-lacking protection of inverter 
outdoor fan   

The water heater stops operation and 
the wired controller displays A0 

Drive module reset of inverter outdoor 
fan   

The water heater stops operation and 
the wired controller displays A0

 

Overcurrent protection of inverter 
outdoor fan   

The water heater stops operation and 
the wired controller displays UP 

Power protection of inverter fan   

The water heater stops operation and 
the wired controller displays AE 

Detection circuit malfunction of driven 
current of inverter outdoor fan   

The water heater stops operation and 
the wired controller displays AJ 

Desynchronizing protection of inverter 
outdoor fan   

The water heater stops operation and 
the wired controller displays A6 

Driven communication malfunction 
between main control and inverter 
outdoor fan   

The water heater stops operation and 
the wired controller displays A8 

High temperature protection of driven 
module of inverter outdoor fan   

The water heater stops operation and 
the wired controller displays A9 

Malfunction of temperature sensor of 
driven module of inverter outdoor fan   

The water heater stops operation and 

Malfunction of drive storage chip of 

Summary of Contents for SWH-200IRA2





















































Reviews:

No comments