Sinclair ASC-60AN User Manual Download Page 11

Function buttons

 

TEMP UP Button

 

Push this button to increase the indoor temperature setting in 1°C 
increments to 30°C.

 

TEMP DOWN Button

 

Push this button to decrease the indoor temperature setting in 1°C 
increments to 17°C.

 

MODE Button

 

Each time the button is pressed, the operation mode is selected in 
the sequence of the following:

 

 

NOTE: Heat mode is for Cooling & Heating models only.

 

SWING Button 

 

Used to stop or start horizontal louver movement. The louver will 
swing up and down automatically if push this button.

 

AIR DIRECTION Button 

 

Used to set the desired up/down air flow direction. The louver 
changes 6 degree in angle for each press.

 

SWING Button 

 

Used to stop or start vertical louver movement .

 

NOTE: This button only available when the remote controller is 
used with corresponding unit.

 

RESET Button

 

Once the recessed RESET button is pressed,

 

all of the current settings will be cancelled

 

and the controller will return to the initial settings.

 

ON/OFF Button

 

Operation starts when this button is pressed and stops when the 
button is pressed again.

 

FAN SPEED Button

 

Used to select the fan speed in four steps:

 

 

FAN SPEED MODE Button

 

Press the Mode and Fan speed button simultaneously for 2 seconds. The remote controls into faceplate setting 
state and the LCD shows F2.Press the TEMP UP( ) to control the faceplate up and press the TEMP DOWN( ) 
to control the faceplate down. Press any button to exit the faceplate setting state, then the LCD back to the 
normal display.

 

TIMER ON Button

 

Press this button to activate the Auto-on time setting. Each press will increase the time setting in 30 minutes 
increments, up to 10 hours, then at 1 hour increments up to 24 hours. To cancel the Auto-on time setting, just 
press the button until the time setting is 0.0.

 

ECO Button

 

Select this function during the sleeping time. It can maintain the most comfortable temperature and save energy. 
This function is available on COOL, HEAT or AUTO mode only . 
NOTE: While the unit is running under Energy-saving mode, it would be cancelled if press MODE, FAN SPEED or 
ON/OFF button.

 

TIMER OFF Button

 

Press this button to activate the Auto-off time setting. Each press will increase the time setting in 30 minutes 
increments, up to 10 hours, then at 1 hour increments up to 24 hours. To cancel the Auto-off time setting, just 
press the button until the time setting is 0.0.

 

LOCK Button

 

Press this recessed button to lock all current settings, and the remote controller will not accept any operation 
except that of the LOCK. Use the LOCK mode when you want to prevent settings from being changed 
accidentally. Press the LOCK button again to cancel the LOCK function. A lock symbol will appear on the remote 
controller display when the lock function is activated.

 

Summary of Contents for ASC-60AN





















Reviews: