background image

 

9

 

 
 
 
HEATING IN OUTDOOR OPERATION  

The unit is outside the room tio be heated. Outdoor operation is ideal for the transition period in which 
outside temperatures do no fall below 7 degrees. 

(If the outside temperature should however fall below 7 degrees 

continuously, we recommend indoor operation). 

Connect the air hose and the air outlet grid to the unit as 

displayed in the illustration, or the air hose connection piece and air outlet grid need to be exchanged. 
 
 
 
 
 
 
 
 
 
 
 
Set the function to “Heating”. The settable temperature range is between 15 and 25 degrees target 
temperature. You can set this using the temperature control. 
 
The air with high oxygen content heated by the   unit is fed into the room via the air hose. This can be 
executed e.g. via a tilted window, a door or wall aperture. Make sure that no warm outside air can enter the 
room. For effective heating, we recommend our selection of various accessories which reduce or prevent 
entry of cold air into the room. 
 
Using the “Comfort Control Kit” you can also control the unit from inside using the remote control. The 
“Comfort Control Kit” set is additional accessories. It is possible to buy it at the seller or supplier. 

 

After switching on, or over, the ventilator operates, but the compressor only starts after the control lamp has flashed for three minutes. 

Cooling effect may require a further 10 minutes. Further information is available under the item, “Troubleshooting”.  

 

 

DEHUMIDIFICATION 

 

Humidity is extracted from the air, collected in the water tank and discharged via the condensation water 
outlet. Only air the room if the humidity of the outside air is below that in the inside room. Set the function to  
“Dehumidity”. 
 

 

 

 

The rubber plug of the condensation water outlet is removed and a drainage hose attached. To collect the 
condensation water easily in a tank, a drainage hose is included in the scope of delivery which you can 
connect to the upper condensation water outlet. Allow water to flow out continuously in order to achieve 
higher dehumidification capacity. In the dehumidify mode, you must not feed the room air outside with the 
extract air hose.  

 

 

 

 

 

 

 

Caution: In the dehumidify mode, separate setting of the ventilator is not provided, since the 
lowest ventilation level is already preset to ensure efficient dehumidification of ambient air. 

.

 

Summary of Contents for AMC-15A













Reviews: