2.1- Programming the first transmitter:
1. Switch the 12 V power supply of the receiver ON. The Led ramp will turn on for two seconds.
2. Select the desired channel*.
3. Press simultaneously the UP and DOWN buttons of the transmitter, the Led ramp
will turn ON for two seconds.
4. Press the
PROG button
1 second, the Led ramp will turn ON for two seconds.
The operation is completed.
2.2- Adding a new transmitter:
1. Select a channel already programmed*.
2. Press for 3 seconds the program button (PROG) until the Led ramp turns ON
for two seconds.
3. Select the channel of the new transmitter you wish to add*.
4. Press the
PROG button
for 1 second, the Led ramp will turn ON for two seconds.
The operation is completed.
5. Press simultaneously the 2
nd
and 4
th
buttons on the TSA+ you wish to add as shown
in the picture, the TSA+’s Led will blink.
6- Press the desired channel (button) on the TSA+ you wish to add, the Led ramp turn
on for two seconds. The operation is completed.
To remove a transmitter (Channel): repeat stages 1, 2 with a transmitter (Channel)
that currently controls the receiver and stage 3,4 or 5,6 with the transmitter (Channel)
to be deleted from the receiver).
2.3- Cancelling programming:
1. Switch off the 12V power supply to the receiver for
2 seconds
.
2. Switch the power to the receiver back on for
7 seconds
.
3. Switch off the power supply to the receiver for
2 seconds
.
4. Switch the power to the receiver back on. The Led ramp will blink for 2 minutes.
5. Press on the transmitter's
PROG button
for more than 7 seconds, the Led ramp will
turn ON for 2 seconds twice in succession. The operation is completed.
* 2.1 (step 2) and 2.2 (step 1 & 3) only in case of multi channel transmitters (COLOR).
EN
LED DC Hz Receiver
5112070C
Carefully read these instructions
before any use.
1/1
Programming
2
Technical characteristics
4
Functioning
3
Led ramp control:
A short press (<0,5 sec.) on the ▲ button to turn the Led ramp on (100%).
A short press (<0,5 sec.) on the ▼ button to turn off the Led ramp (0%).
A short press (<0,5 sec.) on the Stop button to turn ON the Led ramp at the Intermediate Position (ex: 50%).
Led ramp dimming:
A long press (> 0,5 sec.) on the ▲ or ▼ keys increase or decrease the level
of the Led ramp (step: 5% each 0.16 sec, 0% at minimum, 100% at maximum).
Recording/controlling/deleting intermediate position:
- Recording : Press on the ▲ or ▼ button until you reach the desired light level, then press for 5 seconds on the Stop button, the Led ramp will turn ON for 2 seconds.
- Controlling : A short press of the Stop button will the turn ON Led ramp to the memorized intermediate level.
- Deleting : A short press on Stop button and the Led ramp will turn ON to the memorized level. Then press for 5 seconds on the Stop button, the Led ramp will turn on
for 2 seconds.
- Power supply: 12VDC (min.: 11V/max.:16V)
- Control output: 72W at 12V for incandescent/halogen or Led
bulbs.
- Radio: 433.42 MHz
- Storage temperature : -20°C +80°C
- Temperature of use: -20°C +70°C (and exceptionally up to
+80°C (use limited to 5 min))
- Over-current protection on the output.
- Lighting time-out 3 hours.
- Please ensure you dispose of waste products using your
local refuse collection system.
- European compliance: CE
- Protection index : IP 55 — IK Index: IK05.
- Safety level : Class III.
- No need for forced cooling system.
- Frequency range: 433,050 MHz – 434,790 MHz F: 433,420
MHz
- Max power used: ERP < 10 mW.
Led ramp control:
Each press of the button toggles between ON and OFF
No dimming possible with this transmitter.
TRANSMITTERS 1 & 2
TRANSMITTER 3
2 s.
≥ 3 s.
2 s.
2 s.
2 s.
Ch1
Ch2
Ch3
Ch4
Ch5
2 s.
2 s.
+
NEW
NEW
Ch1
Ch2
Ch3
Ch4
Ch5
Ch1
Ch2
Ch3
Ch4
Ch5
PROG
PROG
7 s.
1 s.
PROG
2 s.
1 s.
PROG
new
new
2 s.
< 1 s.
12V
ON
+
2 s.
7 s.
2 s.
OFF
ON
OFF
ON
1.
2.
1.
2.
3.
3.
4.
5.
6.
4.
1.
2.
3.
4.
5.
2 s.
7 s.
> 1 s.
> 1 s.
50%
0%
100%
stop
0%
0%
100%
< 0,5 s.
< 0,5 s.
< 0,5 s.
100%
100%
100%
> 0,5 s.
> 0,5 s.
3 s.
3 s.
< 0,5 s.
< 0,5 s.
0%
100%
50%
IP
2.1
2.2
2.3
Installation
1
Input 12V DC
IN +12V : red
Power supply
12 VDC
IN GND : black
Output 12V DC
84 mm
Ø 4,2 mm (0.165 inch)
24 mm (0.94 inch)
48 mm (1.89 inch)
100 mm (3.94 inch)
420 mm (16.50 inch)
114 x 48 x 18,5 mm (4.49 x 1.89 x 0.73 inch)
6 A
OUT LED +12V : brown
OUT LED GND : blue
AWG18
AWG18
Ø 4 mm
OK
Compatible transmitter (max. 12 per receiver):
1
: COLOR+ Wall Hz transmitter
2
: COLOR+ 1/5 mobile Hz transmitter
3
: TSA+ transmitter
USA : use only FCC transmitter range.
Location of the PROG button on Hz transmitters:
1
1
2
2
3
3
Mandatory instructions:
- Take care not to drill through the Hz DC receiver.
- The receiver power supply line must be equipped with a sectioning, and an over-current protection.
Recommendations:
- This receiver is not protected against load dump.
- Radio appliance using the same frequency (433.42 MHz) may reduce our product’s performance (Ex: Wireless headphones).
- Keep a minimum distance of 8 in. (0.2m) between two Hz receivers. Keep a minimum distance of 12 in. (0.3m) between Hz receivers and Hz transmitters.
- The receiver must be installed by a licensed electrician or a qualified professionnal of motorisation or automation in accordance with these instructions and with local and national
electrical codes.
- The product does not perform electrical insulation and protection, a SELV (Safety Extra Low Voltage) device upstream must be present in order to protect property and persons
according with local and national electrical codes.
US PAT n°7852765/8189620
OR
SIMU hereby declares that the radio equipment covered by these instructions is in compliance with the requirements of Radio Directive 2014/53/EU and the other
essential requirements of the applicable European Directives. The full text of the EU declaration of conformity is available at www.simu.com.
SIMU S.A.S. au capital de 5 000 000 € - Z.I. Les Giranaux - BP71 - 70103 ARC-LÈS-GRAY CEDEX - FRANCE - RCS VESOUL B 425 650 090 - SIRET 425 650 090 00011 - n° T.V.A CEE FR 87 425 650 090