Getting Started
DKIT-02 Lamp Starter Kit
2 Simply Automated, Incorporated
6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA
Technical Support:
www.simply-automated.com
or
800-630-9234
452-0002-1001 Rev. D Revised: September 13, 2011
Simply Automated Pre-Configured SimplySmart
TM
Series
Utilizes SimplySmart
TM
technology to make installation a breeze. No computer programming required!
Simple-n-easy, ready to use lighting control.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic safety precautions should always be followed, including the following:
1.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2.
Keep away from water. If product comes into contact with water or other liquid, disconnect immediately.
3.
Never use products that have been dropped or damaged.
4.
Do not use this product outdoors.
5.
Do not use this product for other than its intended use.
6.
Do not connect multiple lamps that, when combined, exceed the maximum load rating of the product.
7.
To avoid risk of fire, burns, personal injury and electric shock, install this product out of reach of small children.
8.
Do not install in areas that can exceed 120°F (e.g., in an attic).
9.
Do not cover the product with any material when in use.
10. This product uses polarized plugs and sockets (one blade is wider than the other) to reduce the risk of electric shock. These plugs and
sockets fit only one way. If they do not fit, consult a technician. Do not use with an extension cord unless plugs can be fully inserted.
Do not alter plugs.
11.
SAVE THESE INSTRUCTIONS.
DKIT-02 Lamp Starter Kit
Includes 2 Lamp Modules and 1 Tabletop Scene Controller with 4-Buttons
Getting Started
Section 1: Very Important Pre-Installation Notes
•
Your home should be no more than 2500 square feet and have only one breaker panel. A phase coupler is
required in some home installations; especially homes > 2500 square feet or homes with more than 1
breaker panel. See Section 5 for more information.
•
Not intended for use in multi-dwelling (condo, apartment) buildings with 3-phase power.
•
Do not reset to factory default configuration, pre-configured settings will be lost.
•
software and a
or Scheduler-Timer can be used with a PC for
customizing pre-configured units and checking performance.
Section 2: Installation of Lamp Modules and Tabletop Controller
Choose a convenient location you would like to use for the main controller and plug in the Tabletop Controller
with 4-buttons. Locate 2 lamps you would like to turn ON/OFF. Plug a lamp module into a wall outlet, then
plug-in a lamp into the socket on the bottom of the lamp module. Turn the lamp ON using the lamp’s ON/OFF
switch. Repeat this process for second lamp module. You're done with the installation process! If necessary,
please refer to the User Guide enclosed in the lamp module product box, or see
http://simply-
automated.com/documents/452-0112-0201_RevC_UML-E-W_UserGuide_090512.pdf
.
Test Tabletop Controller with 4-buttons to ensure proper installation:
•
Button 1 turns on/off lamp module labeled #4: Press (tap) button 1 one time to turn on lamp module #4,
press and hold to dim up/down, press (quickly tap) two times to turn off.
•
Button 2 turns on/off lamp module labeled #5: Press (tap) button 2 one time to turn on lamp module #5,
press and hold to dim up/down, press (quickly tap) two times to turn off.
•
Button 3 turns on/off both lamp modules: Press (tap) button 3 one time to turn on both lamp modules,
press and hold to dim up/down, press (quickly tap) two times to turn off.
•
Button 4 turns off both lamp modules: Press (tap) button 4 one time to turn off both lamp modules.
