background image

5

SimpliFire  •  SF-INS30-BK  •  2042-980  Rev. B  •  12/18

Note:

  The device complies with Part 15 of the FCC Rules.  

Operation is subject to the following two conditions:
1.  This device may not cause harmful interference.
2.  This device must  accept any interference received, 

 

    including interference that may cause undesired  

      operation.

MODELS:

  SF-INS30-BK

LABORATORY:  

CSA International

TYPE:  

Electric Air-Heaters; Fixed and Location-Dedicated  

             Electric Room Heaters

STANDARD:

 CSA C22.2  No 46-13; UL 2021 (4

th

 Edition)

A.  Appliance Certification

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.  

This appliance is tested and approved as either supplemen

-

tal room heat or as a decorative appliance.  It should not be 

factored as primary heat in residential heating calculations.

NOTICE: This installation must conform with local codes. 

GENERAL INFORMATION 

  

B.  Unpacking and Inspecting Appliance 

WARNING! DO NOT use this Electric Fireplace if any 

part has been under water.  Immediately call a qualified 

service technician to inspect and to replace any part of 

the electrical system if necessary.  Keep plastic wrapping 

away from children.

•  Carefully remove the appliance and components from 

the packaging.  Discard packaging.

•  Carefully inspect components for any damage. 
•  Reference parts and hardware list to verify all parts have 

been received.

•  Report to your dealer any missing or damaged parts.
•  Read all the instructions before starting the installation.  

Follow these instructions carefully during the installation 

to ensure maximum safety and benefit.

C.  Model and Serial Number Information 

 

The model and serial number information is located on 

the rating plate.  The rating plate is located on the upper 

wall of the fireplace behind glass front. 

Model Name: ___________________________________________ Date purchased/installed: __________________

Serial Number: __________________________________________

Location on fireplace:

 _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

We recommend that you record the following pertinent 

information about your fireplace.

Homeowner Reference Information

WARNING:  

This product can expose you to Di-

(2-ethylhexyl) phthalate, which is known to the 

State of California to cause cancer and reproductive 

harm.  For more information go to: www.P65Warnings.

ca.gov.

Summary of Contents for SF-INS30-BK

















Reviews: