background image

1

SimpliFire •  SF-INS25, SF-INS30, SF-INS35 Service Manual  •  2042-960  •  3/21

SERVICE MANUAL

Model: SF-INS25, SF-INS30, SF-INS35

- Instructions -

This manual will assist a qualified service technician in the 

replacement of parts.  Contact your dealer to arrange a 

service call by a qualified service technician.

CAUTION! Risk of Cuts, Abrasions or Flying Debris. 

Wear protective gloves and safety glasses during 

installation and service. Sheet metal edges are sharp.

WARNING: If the information in these 

instructions is not followed exactly 

it may result in personal injury and/or 

property damage.

Tools and Supplies Needed

Before beginning the installation be sure that the following 

tools and building supplies are available.
Pliers 

 

Phillips screwdriver 
Safety glasses 
Flat blade screwdriver 

Front Replacement (STFRONT-INS** /  

FT-MISSION-**)

1.  If necessary, place a drop cloth or other material on 

     the hearth or flooring to prevent scratching.  

 

 

2.  Grasp front with two hands.   Lift up and off of the ap-

 

     pliance.
3.  Install replacement front by aligning the hooks on the 

 

     back side of the door to the slots in the appliance.  

 

     Press evenly down with two hands to fully engage the 

 

     front to the appliance.

NOTICE!  DO NOT discard any hardware while 

servicing. 

It must be reused.

WARNING! Risk of Shock!  

  

Always disconnect power before 

disassembly or servicing. 

Replacement parts include:

Description

Part Number(s)

Front

STFRONT-INS**

FT-MISSION-**

Glass

GLAS-INS**

Interior Side Panels

PANEL-INS**

Log/Grate Assembly 

 LOG-INS**

Flame Screen

FLAM-INS**

Remote

REMOTE-INS30

LED Lighting

 LED-INS**

Heater/Control Board 

Assembly

HEAT-INS**

Rotisserie Motor and 

Rod

 ROTISS-INS**

Remote Receiver

RECEIVER-ELECT

Hardware

HRDW-BI

Replacement Instructions

Summary of Contents for SF-INS25










Reviews: